Werbung
Verfügbare Sprachen
Verfügbare Sprachen
ENGLISH
GENERAL
MINISYSTEM is a DC welding machine family based on
the inverter technology, where you can choose the right
product
for MMA, MMA/TIG,
TIG/MIG-MAG welding
There
are two size classes
power sources: I-phase 150 A and 3-phase 240 A.
The MINISYSTEM products include complete operations
for professional use for different welding methods and
they can be equipped
with versatile remote control and
transport
units.
MINISYSTEM
PRODUCT
PRODUCT
UNITS
RJikkO
MP 1500
MP1500 power source
MP 2400
MP2400powersource
MMA,'TIG
MP 1500 TIG
MP 1500 + MTC
MP 2400 TIG
MP 2400
MMAtMlG
MP 1500 MIG
MP 1500 + MM05
MP
MIG
MP 2400
MMA•TIG'MIG
MP1500TRIO
MP 1500 + MTC+
MM 05
MP 24ØTRlO
MP2400
MM 20
REMOTE
CONTROL
MMA and TIG welding
C 100C, CIOOD, C IOOF, C IOOP
MIG welding
c 120S, c 130S, c 1100.
BASIC
DATA
MINISYSTEM
Mains connection 1—,200-240 V, 50/60 Hz
Fuse
16 A delayed
Current ranges.
MMA
15 A -150 A
TIG
5 A-150A
MIG
10 A -150 A
OPERATING
INSTRUCTIONS
MINISYSTEM
MMA:
Technical data of the power source and MMA welding.
MINISYSTEM
TIG:
TIG welding and technical data.
MINISYSTEM
MIG-MAG:
MIG welding and technical
NOTE !
Operating instructions for each method are valid also
for multi-method
INSTALLATION
The device has to be placed on a steady chassis from which
1914350
MMA/MIG-MAG
or MMN
in the MINISYSTEM
inverter
FAMILY
DIMENSIONS
lengthwidthheightæght
mm
mm
mm
375 x 205 x 325
375 x 205 x 360
375 X 205 x 440
MTLG
375 x 205 x 510
435 x Z35x 615
MM 20
235x830
4.35 x 235* 725
MTLG +
435*
235x975
UNITS
1500
MINISYSTEM
2400
F, 380-415 V, 50/60 Hz
10 A delayed
15 A -200 A
5A-250A
10 A - 230 A
data.
products.
there doesn't come dust among suction air.
The ventilation
should be ensured. The machine should be
protected against hard rain and under hot circumstances against
direct sun light.
Clean the machine regularly from dust and dirt with a vacum
cleaner.
CONNECTION
OF PRIMARY CABLE TO THEANNS
SHOULD
ONLY BE CARRIED
TRICIAN.
For the connection
the connection cable side. For the cable there is an inlet ring
on the rear panel of the machine and a cable clamp on the
mounting
bottom. Connect the cables onto the terminal block
according to markings (see page 2).
GUARANTEE
The machines produced and products represented by Kemppi
Oy are guaranteed against defects in material or manufacture.
Within the limits of the guarantee the defective part will be
replaced by a new one, or when possible, repaired free of charge.
The guarantee is valid for one year provided that the machine
is used
in one-shift
The guarantee
does not compensate
kg
proper use, neglect or normal wear. Possible travelling costs
or freight or postage charges are not covered by the Kemppi
12
18
guarantee.
Guarantee repairs shall be carried out only by Kemppi aut-
16
horised representative.
24
a certificate about validity of guarantee has to be presented.
20
28
24
POWER
SOURCES
34
The MINISYSTEM
The operations of the control switches and connections
power source are similar in all products of the product family.
SWITCHES AND CONTROLS (Seepage2)
Main
switch
SII
In I-position the control circuits of the machine get voltage
and the signal lamp HI I of the front panel is lit.
Local control potentiometer
Control of welding current either according to current or
memory scale.
Local/remote
control
selector
S12
In switch'es
position
goes over to the remote control unit. The operation is the same
with MMA, TIG and MIG methods.
Method
selector
S13
The switch'es
position
method.
Markings
for MMA,
MAG.
CONNECTORS
Welding current connectors
With the TIG method connect the earthing cable to the positive
pole, with the MIG method to the negative pole.
With the MMA methodyou can selectthe polarity of the welding
attachments, because the positive and negative DIX connectors
are similar.
OUT BY A COMPETENT
remove the side plate of the machine from
work.
for damage due to im-
In case guarantee repair is demanded
power sources are MP 1500 and MP 2400.
RII
the control of the power source
is selected
according
for TIG,
XII
and X12
SUPPLY
ELEC-
of the
to the welding
for M
7
Werbung
