Silvercrest RHYTHM Bedienungs- Und Sicherheitshinweise Seite 18

Once charging has completed, remove the USB type C plug on
the USB Cable (Type A to C)
Using the headphones
Connect the headphones with a communication device.
Place the headphones near a switched on communication
device (e.g. mobile or computer).
Pairing with a new Bluetooth
Button for approx. 2 seconds until the LED
6
and white alternately. This indicates the headphones are now
ready to connect mode, which remains active for 5 minutes. If the
pairing with a playback device has not been established after 5
minutes, the headphones switch off automatically.
Now connect your communication device (mobile phone or
computer) via Bluetooth
®
to the notes in the instructions for your communication device.
Select the entry "Rhythm On-Ear ANC" from the list of devices
detected by your computer or mobile.
Once the connection has been established, the LED
white every 5 seconds.
Please note, your communication device must support Bluetooth
Standard 5.3 to use all options.
You may need to approve the connection on the communication
device. Please refer to the instructions for use of the communi-
cation device on this topic!
The headphones may be manually switched off by holding the
Multi Function Button
6
off.
Bluetooth indicator:
®
LED indicator status
Flashing red and white
Flashing white once every 5 seconds Paired
Connecting the headphones to
a second Bluetooth
The headphones may be connected to two Bluetooth
tion devices at the same time. If the headphones are already connected
to a device, follow the steps below to connect to the second device:
Activate multipoint mode by pressing and holding Bluetooth
button for 2 seconds. The first communication device (mobile
11
phone or computer) is disconnected.
Now connect to the second communication device via Bluetooth
with the headphones. Please refer to the notes in the instructions
18 GB/IE
from the headphones.
14
device: Hold the Multi Function
®
flashes red
10
with the headphones. Please refer
will flash
10
for 5 seconds until the LED
10
Headphone state
Pairing mode
device
®
communica-
®
for your communication device. Select the entry "Rhythm On-
Ear ANC" from the list of devices detected by your computer
or mobile. The second communication device is connected.
Select the entry "Rhythm On-Ear ANC" from the list of devices
detected by your first communication device/computer. Now,
both communication devices are connected to the headphones
simultaneously.
After connected the headphone with 2 Bluetooth
you can playback music via either one of device.
Clearing paired devices
You can clear up the paired device anytime. Please make sure
headphone Bluetooth
press both Bluetooth
together at the same time for approx. 2 seconds.
The memory in the headphones is cleared and it will not
auto-connected to the previous paired communication device.
Connecting the headphones
through audio cable
®
Insert the audio cable with 3.5 mm jack plug
jack socket .
8
Insert the other audio cable with 3.5 mm jack plug
jack socket of your playback device.
goes When a 3.5 mm cable is plugged into the 3.5 mm jack socket
, the Bluetooth
8
function turns OFF.
Start a playlist on your playback device. You can only adjust
the music volume on the playback device.
Active Noise Cancellation function (ANC)
In order to filter out unwanted noises from surrounding you can
enable the active noise cancellation (ANC) function.
Press once the ANC button
function and an acoustic signal will sound.
Voice control function with Siri/
Google assistant
®
Please follow below steps to activate the Voice Control function:
®
1. First activate Siri or Google assistent on you mobile device.
is under disconnected status. Please
®
button and Multi Function Button
® 11
13
connection will be disconnected. The ANC
®
to switch ON/OFF the ANC
9
devices,
®
6
to 3.5 mm
to 3.5 mm
13