Sony XR-L500 Bedienungsanleitung
Inhaltsverzeichnis
Quicklinks
XR-L500/L500V/L500X
SERVICE MANUAL
Ver 1.1 2001.05
Cassette Player section
Tape track
Wow and flutter
Frequency response
Signal-to-noise ratio
Tuner section
FM
Tuning range
Aerial terminal
Intermediate frequency
Usable sensitivity
Selectivity
Signal-to-noise ratio
Harmonic distortion at 1 kHz
Separation
Frequency response
MW/LW
Tuning range
Aerial terminal
Intermediate frequency
Sensitivity
Power amplifier section
Outputs
Speaker impedance
Maximum power output
Sony Corporation
9-870-247-12
2001E0500-1
e Vehicle Company
C 2001.5
Shinagawa Tec Service Manual Production Group
Photo: XR-L500
SPECIFICATIONS
4-track 2-channel stereo
0.08 % (WRMS)
30 – 18,000 Hz
Cassette type
TYPE II, IV
61 dB
TYPE I
58 dB
87.5 – 108.0 MHz
External aerial connector
10.7 MHz/450 kHz
8 dBf
75 dB at 400 kHz
66 dB (stereo),
72 dB (mono)
0.6 % (stereo),
0.3 % (mono)
35 dB at 1 kHz
30 – 15,000 Hz
MW: 531 – 1,602 kHz
LW: 153 – 279 kHz
External aerial connector
10.7 MHz/450 kHz
MW: 30 µV
LW: 40 µV
Speaker outputs
(sure seal connectors)
4 – 8 ohms
50 W × 4 (at 4 ohms)
Model Name Using Similar Mechanism
Tape Transport Mechanism Type
General
Outputs
Audio outputs (Rear)
Power aerial relay control
lead
Power amplifier control lead
Inputs
Telephone ATT control lead
Remote controller input
connector
Aerial input connector
Bass ±8 dB at 100 Hz
Tone controls
Treble ±8 dB at 10 kHz
Loudness
100 Hz +8 dB
10 kHz +2 dB
Power requirements
12 V DC car battery
(negative earth)
Approx. 178 × 50 × 176
Dimensions
mm (w/h/d)
Approx. 182 × 53 × 161
Mounting dimensions
mm (w/h/d)
Mass
Approx. 1.2 kg
Supplied accessories
Parts for installation and
connections (1 set)
Front panel case (1)
Note
This unit cannot be connected to a digital preamplifier
or an equalizer.
Design and specifications are subject to change
without notice.
FM/MW/LW CASSETTE CAR STEREO
AEP Model
UK Model
XR-4300R
MG-25G-136
Inhaltsverzeichnis
Verwandte Anleitungen für Sony XR-L500
Inhaltszusammenfassung für Sony XR-L500
- Seite 1 XR-L500/L500V/L500X SERVICE MANUAL AEP Model UK Model Ver 1.1 2001.05 Photo: XR-L500 Model Name Using Similar Mechanism XR-4300R Tape Transport Mechanism Type MG-25G-136 SPECIFICATIONS General Cassette Player section Outputs Audio outputs (Rear) Tape track 4-track 2-channel stereo Power aerial relay control Wow and flutter 0.08 % (WRMS)
-
Seite 2: Inhaltsverzeichnis
6-7. Schematic Diagram – SUB Board – ....... 19 6-8. Printed Wiring Board – KEY Board (XR-L500/L500X) – ........ 20 6-9. Printed Wiring Board – KEY Board (XR-L500V) – ..21 6-10. Schematic Diagram – KEY Board – ......22 6-11. -
Seite 3: General
XR-L500/L500V/L500X SECTION 1 This section is extracted from instruction manual. GENERAL Location of controls Refer to the pages listed for details. : During tape playback : During radio reception : During menu mode TAPE RADIO MENU MENU SEEK SEEK SOUND... -
Seite 4: Setting The Clock
XR-L500/L500V/L500X Setting the clock The clock uses a 24-hour digital indication. Example: To set the clock to 10:08 Press (MENU), then press either side of (DISC/PRESET) or (PRESET) repeatedly until “CLOCK” appears. 1 Press (ENTER). The hour indication flashes. 2 Press either side of (DISC/PRESET) or (PRESET) to set the hour. - Seite 5 XR-L500/L500V/L500X AUDIO OUT Nota per il collegamento dell’antenna Note for the aerial connecting If your car aerial is an ISO (International Se la vostra antenna della macchina è di Organisation for Standardisation) type, use tipo ISO (International Organization the supplied adaptor 7 to connect it.
- Seite 6 XR-L500/L500V/L500X Cautions Vorsicht Précautions Attenzione Let op! • This unit is designed for negative earth 12 V DC operation only. • Dieses Gerät ist ausschließlich für den Betrieb bei 12 V • Cet appareil est conçu pour fonctionner sur courant continu de •...
- Seite 7 XR-L500/L500V/L500X Dashboard Fire wall Armaturenbrett Motorraumtrennwand Tableau de bord Paroi ignifuge Cruscotto Parete tagliafiamma Dashboard Brandschot 1 8 2 Bend these claws outward for a 5 3 m tight fit, if necessary. Falls erforderlich, diese Klammern für einen sicheren Halt hochbiegen.
-
Seite 8: Disassembly
XR-L500/L500V/L500X SECTION 2 DISASSEMBLY • This set can be disassembled in the order shown below. 2-1. DISASSEMBLY FLOW Note 1: The process described in can be performed in any order. Note 2: Without completing the process described in , the next process can not be performed. -
Seite 9: Main Board
XR-L500/L500V/L500X 2-3. MAIN BOARD 3 rubber cap (25) 2 three ground point screws (PTT2.6 × 6) 1 three screws (PTT2.6 × 8) 4 main board 2-4. HEAT SINK (ISO2P) 1 two screws (PTT2.6 × 8) 3 heat sink (ISO2P) 2 two screws (PTT2.6 ×... -
Seite 10: Assembly Of Mechanism Deck
XR-L500/L500V/L500X SECTION 3 ASSEMBLY OF MECHANISM DECK Note: Follow the assembly procedure in the numerical order given. 3-1. HOUSING 7 Hold the hanger by bending the claw. 5 Fit projection on C part. 1 Install the catch to the hanger. -
Seite 11: Lever (Ldg-A)/(Ldg-B)
XR-L500/L500V/L500X 3-3. LEVER (LDG-A) / (LDG-B) shaft A shaft A shaft B shaft B shaft C 1 Fit the lever (LDG-A) on 3 type-E stop ring 2.0 shafts A – C and install it. 2 Fit the lever (LDG-B) on shafts A and B and install it. -
Seite 12: Guide (C)
XR-L500/L500V/L500X 3-5. GUIDE (C) 2 guide (C) 1 three claws 3-6. MOUNTING POSITION OF CAPSTAN/REEL MOTOR (M901) two precision screws (P2 × 2) capstan/reel motor (M901) Note: Mount the motor so that the angle between of the motor and the hole for the becomes 30 °... -
Seite 13: Mechanical Adjustments
XR-L500/L500V/L500X SECTION 4 SECTION 5 MECHANICAL ADJUSTMENTS ELECTRICAL ADJUSTMENTS 1. Clean the following parts with a denatured-alcohol-moistened TAPE DECK SECTION 0 dB=0.775 V swab: playback head pinch roller Tape Speed Adjustment rubber belt capstan Setting: idler 2. Demagnetize the playback head with a head demagnetizer. -
Seite 14: Diagrams
XR-L500/L500V/L500X SECTION 6 DIAGRAMS 6-1. NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS Note on Printed Wiring Board: Note on Schematic Diagram: • All capacitors are in µF unless otherwise noted. pF: µµF • X : parts extracted from the component side. -
Seite 15: Printed Wiring Board - Main Board
XR-L500/L500V/L500X 6-2. PRINTED WIRING BOARD – MAIN Board – AUDIO OUT (REMOTE IN) REAR FM/AM ANTENNA IN MAIN BOARD CN781 (FRONT VIEW) CN781 F781 14 13 IC751 REAR RCH+ FRONT RCH+ FRONT LCH+ REAR LCH+ GRN/BLK REAR LCH– WHT/BLK FRONT LCH–... -
Seite 16: Schematic Diagram - Main Board (1/3)
XR-L500/L500V/L500X 6-3. SCHEMATIC DIAGRAM – MAIN Board (1/3) – • • See page 14 for Waveform. See page 23 for IC Block Diagrams. (Page 17) (Page 18) -
Seite 17: Schematic Diagram - Main Board (2/3)
XR-L500/L500V/L500X 6-4. SCHEMATIC DIAGRAM – MAIN Board (2/3) – • • See page 14 for Waveforms. See page 23 for IC Block Diagrams. (Page 16) (Page 18) -
Seite 18: Schematic Diagram - Main Board (3/3)
XR-L500/L500V/L500X 6-5. SCHEMATIC DIAGRAM – MAIN Board (3/3) – • See page 23 for IC Block Diagram. (Page 16) (Page 19) (Page 17) -
Seite 19: Printed Wiring Board - Sub Board
XR-L500/L500V/L500X 6-6. PRINTED WIRING BOARD – SUB Board – 6-7. SCHEMATIC DIAGRAM – SUB Board – SUB BOARD (COMPONENT SIDE) TAPE DECK ILLUMINATION LED801 K1 S2 K2 A1 S1 A2 LSW801 (Page 22) 1-676-603- (21) MAIN BOARD CN701 (Page 15) -
Seite 20: Printed Wiring Board - Key Board (Xr-L500/L500X)
XR-L500/L500V/L500X 6-8. PRINTED WIRING BOARD – KEY Board (XR-L500/L500X) – KEY BOARD (COMPONENT SIDE) (L500/L500X) R964 LED902.S907 R965 R940 R941 PRESET LIQUID CRYSTAL DISPLAY LED905, 910 LED906, 909 SOURCE LED900, 901 (LCD BACK LIGHT) ENTER (LCD BACK LIGHT) (KEY ILLUMINATION) -
Seite 21: Printed Wiring Board - Key Board (Xr-L500V)
XR-L500/L500V/L500X 6-9. PRINTED WIRING BOARD – KEY Board (XR-L500V) – LED900, 903, LED913, 914 KEY BOARD (COMPONENT SIDE) (L500V) LED913,914 (KEY ILLUMINATION) LED902.S902 R965 R940 PRESET (LCD BACK LIGHT) (LCD BACK LIGHT) LIQUID CRYSTAL DISPLAY SOURCE LED900, 901 ENTER (KEY ILLUMINATION) -
Seite 22: Schematic Diagram - Key Board
XR-L500/L500V/L500X 6-10. SCHEMATIC DIAGRAM – KEY Board – • See page 14 for Waveform. (Page 19) -
Seite 23: Ic Block Diagrams
XR-L500/L500V/L500X • IC Block Diagrams – MAIN Board – IC51 SAA6588T-118 POWER SUPPLY PAUSE & RESET DETECTOR MULTI PATH 57kHz DETECTOR 8th ORDER BAND-PASS FILTER CLOCKED SIGNAL QUALITY COMPARATOR DECODER CLOCK CLOCK RDS/RDBS RDS/RDBS INTERFACE DATA DEMODULATOR DECODER REGISTER DATA... - Seite 24 XR-L500/L500V/L500X IC331 TDA7406T MIXER SPECTRUM SACLK ANALYZER FRONT REAR OUTPUT SELECTOR SWIN 34 ACINR 35 MAIN WOOFER FILTER ACOUTR 36 QUAL HIGH-CUT QUAL PULSE S & H SWACOUT 37 FORMER 25kHz ACOUTL 38 7 BAND EQUALIZER MPOUT MULTIPATH DEMODULATOR DETECTOR...
- Seite 25 XR-L500/L500V/L500X IC351 LB1930M-TLM BUFFER OUT1 MOTOR CONTROL DRIVE CIRCUIT CIRCUIT OUT2 BUFFER P-GND S-GND IC611 BA4908-V3 REGULATOR OVER VOLTAGE PROTECT – 2 3 4...
-
Seite 26: Ic Pin Function Description
Reset signal output to the SONY bus interface “L”: reset Not used (pull up) BUSON Bus on/off control signal output to the SONY bus interface “L”: bus on Not used (pull up) Input of acknowledge signal for the key entry Acknowledge signal is input to accept function KEYACK and eject keys in the power off status On at input of “H”... - Seite 27 Serial data input from the SONY bus interface Not used (fixed at “L”) BUSCKO Serial data transfer clock signal output to the SONY bus interface Not used (open) Two-way data IIC bus with the FM/AM tuner unit (TU1), RDS decoder (IC51) and electrical...
- Seite 28 XR-L500/L500V/L500X Pin No. Pin Name Description Power on/off control signal output of the illumination LED and liquid crystal display driver ILLON (IC900) “H”: power on Rotation detection signal input from supply reel sensor and take-up reel sensor on the mechanism...
-
Seite 29: Exploded Views
XR-L500/L500V/L500X SECTION 7 EXPLODED VIEWS NOTE: • Items marked “*” are not stocked since they • -XX and -X mean standardized parts, so they may have some difference from the original are seldom required for routine service. Some one. delay should be anticipated when ordering these items. -
Seite 30: Front Panel Section
XR-L500/L500V/L500X 7-2. FRONT PANEL SECTION (L500V) not supplied (KEY board) (L500V) LCD901 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark X-3380-080-1 KNOB (VOL) ASSY (L500V/L500X) * 61 3-223-799-01 PLATE (LCD), GROUND X-3380-081-1 KNOB (VOL) ASSY (L500) -
Seite 31: Mechanism Deck Section (Mg-25G-136)
XR-L500/L500V/L500X 7-3. MECHANISM DECK SECTION (MG-25G-136) HP901 M901 not supplied Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark A-3291-667-A CLUTCH (FR) ASSY 3-933-346-01 CATCHER * 152 3-019-130-01 LEVER (LDG-A) 3-933-344-01 GUIDE (C) * 153 3-019-131-01 LEVER (LDG-B) -
Seite 32: Electrical Parts List
XR-L500/L500V/L500X SECTION 8 ELECTRICAL PARTS LIST NOTE: When indicating parts by reference • Due to standardization, replacements in the • Items marked “*” are not stocked since they number, please include the board. parts list may be different from the parts speci- are seldom required for routine service. - Seite 33 XR-L500/L500V/L500X Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark LSW904 1-771-476-11 SWITCH, KEY BOARD (WITH LED) R914 1-216-819-11 METAL CHIP 1/16W (MODE o) (L500V/L500X) R915 1-216-819-11 METAL CHIP 1/16W LSW904 1-786-112-11 SWITCH, KEY BOARD (WITH LED)
- Seite 34 XR-L500/L500V/L500X MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R953 1-216-025-00 METAL CHIP 1/10W S907 1-786-175-21 SWITCH, TACT (WITH LED) (MBP) (L500V) ************************************************************** R954 1-216-809-11 METAL CHIP 1/16W R955 1-216-809-11 METAL CHIP 1/16W A-3326-808-A MAIN BOARD, COMPLETE (L500)
- Seite 35 XR-L500/L500V/L500X MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C183 1-163-251-11 CERAMIC CHIP 100PF C602 1-109-982-11 CERAMIC CHIP C184 1-107-823-11 CERAMIC CHIP 0.47uF (L500V) C185 1-163-009-11 CERAMIC CHIP 0.001uF C611 1-126-157-11 ELECT 10uF C191 1-163-009-11 CERAMIC CHIP 0.001uF...
- Seite 36 XR-L500/L500V/L500X MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark D708 8-719-056-83 DIODE UDZ-TE-17-6.8B JC502 1-216-296-11 SHORT D709 8-719-056-83 DIODE UDZ-TE-17-6.8B JC558 1-216-295-11 SHORT D710 8-719-056-83 DIODE UDZ-TE-17-6.8B JC565 1-216-295-11 SHORT D711 8-719-056-83 DIODE UDZ-TE-17-6.8B D712 8-719-056-83 DIODE UDZ-TE-17-6.8B...
- Seite 37 XR-L500/L500V/L500X MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 1-216-097-11 RES-CHIP 100K 1/10W R502 1-216-049-11 RES-CHIP 1/10W R507 1-216-049-11 RES-CHIP 1/10W 1-216-069-00 METAL CHIP 6.8K 1/10W R508 1-216-049-11 RES-CHIP 1/10W 1-216-025-11 RES-CHIP 1/10W R509 1-216-049-11 RES-CHIP...
- Seite 38 XR-L500/L500V/L500X MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R579 1-216-097-11 RES-CHIP 100K 1/10W 1-676-603-21 SUB BOARD (L500/L500V) ********** R586 1-216-073-00 METAL CHIP 1/10W 1-792-195-11 CABLE, FLEXIBLE FLAT (14 CORE) R587 1-216-073-00 METAL CHIP 1/10W...
- Seite 39 XR-L500/L500V/L500X Ver 1.1 2001.05 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 3-227-103-21 MANUAL, INSTRUCTION, INSTALL (ENGLISH, SPANISH, SWEDISH, PORTUGUESE, GREEK, RUSSIAN) 3-227-103-31 MANUAL, INSTRUCTION, INSTALL (ENGLISH, CZECH, POLISH, TURKISH, RUSSIAN) (L500/L500X) X-3378-490-1 CASE (PANEL) ASSY (for FRONT PANEL)
-
Seite 40: Revision History
XR-L500/L500V/L500X REVISION HISTORY Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper right on the revised page allows you to jump to the next revised page. Ver. Date Description of Revision 2001.05...