Atlas Copco Control Thin Legic Sicherheitshinweise Seite 4

Safety Information
Designated Standards applied:
EN 300330 V2.1.1 EN 301 489-1 V2.2.3 EN
301 489-3 V2.3.2, EN IEC 61000-6-2:2019 EN
IEC 61000-6-3:2021 EN 62368:2014/A11:2017
EN IEC 63000:2018
Authorities can request relevant technical information from:
Product Compliance Manager, Atlas Copco Industrial Tech-
nique AB, SE-105 23 Stockholm Sweden
Stockholm, 1 November 2022
Lars Eklöf, Managing Director
Signature of issuer
Authorised Representative UK
James McAllister, General Manager
Atlas Copco Ltd
Swallowdale Lane
Hemel Hempstead
Hertfordshire HP2 7EA
FCC and ISED Compliance Statement
This device complies with part 15 of the FCC Rules. Opera-
tion is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) this device must
accept any interference received, including interference that
may cause undesired operation.
FCC Responsible party:
Name: Rodney Hill
Position: Product Marketing Manager
Address: 3301 Cross Creek Parkway
MI 483 26 Auburn Hills
United States
Mobile: +1 919 272 7837
Email: rodney.hill@us.atlascopco.com
The device is only in compliance if no changes or modifica-
tions are made to the device. The antenna is fixed to the de-
vice and no change in antenna or fixation of the antenna is ac-
ceptable and such modification is considered to violate the
Compliance Statement.
4 © Atlas Copco Industrial Technique AB - 9846 1192 00
Assembly Control Thin Legic
NOTE: This equipment has been tested and found to
comply with the limits for a Class B digital device, pur-
suant to part 15 of the FCC Rules. These limits are de-
signed to provide reasonable protection against harmful
interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the in-
structions, may cause harmful interference to radio com-
munications. However, there is no guarantee that inter-
ference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or
television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit dif-
ferent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV tech-
nician for help.
ISED Compliance Statement:
This device complies with: CAN ICES-3 (B)/NMB-3(B)
(English) This device complies with Industry Canada's li-
cence-exempt RSSs. Operation is subject to the following two
conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including inter-
ference that may cause undesired operation of the device.
(French) Le présent appareil est conforme aux CNR d'Indus-
trie Canada applicables aux appareils radio exempts de li-
cence. L'exploitation est autorisée aux deux conditions suiv-
antes:
1) l'appareil ne doit pas produire de brouillage;
2) l'appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d'en compromettre le
fonctionnement.
Information regarding Article 33 in REACH
The European Regulation (EU) No. 1907/2006 on Registra-
tion, Evaluation, Authorization and restriction of Chemicals
(REACH) defines among other things requirements related to
communication in the supply chain. The information require-
ment applies also to products containing so called Substances
of Very High Concern (the "Candidate List"). On 27 June
2018 lead metal (CAS nr 7439-92-1) was added to the Candi-
date List.
In accordance with the above this is to inform you that certain
mechanical components in the product may contain lead
metal. This is in compliance with current substance restriction
legislation and based on legit exemptions in the RoHS Direc-
tive (2011/65/EU). Lead metal will not leak or mutate from
the product during normal use and the concentration of lead
metal in the complete product is well below the applicable
threshold limit. Please consider local requirements on the dis-
posal of lead at product end of life.