RONDELL RDE-1117 Betriebsanweisung Seite 23

A. Pour the descaling agent into a container with clean water and
wait until it completely dissolves.
Descaling agents should be used in accordance with
the recommendations of the manufacturer of cleaning
products!
B. Open the water tank (2) lid (1) and fill it with cleaning solution
to the maximal level.
Place a suitable container with a capacity of at least 1,5 liters
on the metal drip tray (11) and adjust the height of the coffee
spout (9).
C. In the standby mode, press and hold the button «MENU/
EXIT» « » for 3 seconds to enter the settings menu, and
then press the button «MENU/EXIT» «
and go to the descaling interface, while the icon «
pears on the control panel display. To start the process, press
the button «STEAM/OK» «
D. During decalcination, the cleaning solution will start to exit
alternately from the coffee supply unit (9) openings and from
the steam supply tube (15) into the prepared container, while
the icon « » will flash. When the cleaning solution in the
tank runs out, the« » icon will flash on the display and
you will hear sound signals, pour the remaining third of the
cleaning solution into the water tank and add clean water
to the maximum level. The descaling process will continue
automatically. At the end of the process, two icons «
and « » will appear on the control panel (7). Cleaning is
required.
Do not use a dish-washing machine for cleaning the removable parts!
Service Item
Brewing Unit Remove the brewing unit, rinse it with running water
(13) from the top side, remove the coffee grounds from the
surface of the piston filter. It is suggested to clean by
hand every 3 days! Do not remove the lubricating oil on
the bottom and middle side of the brewing unit.
Steam supply 1. Each time after frothing the milk, put it into a cup with
tube with clean water for rinsing. Then proceed in the same way
metal tip (15) as when frothing. Wipe the surface of the metal tip and
keep it clean.
2. Remove the metal tip and rinse the steam supply
tube every day after use.
» 4 more times
» ap-
» (fig. 18).
»
Maintenance Methods
23
E. Remove the water tank and empty any remaining descaling
solution. Rinse the tank under running water, reinstall into the
coffee machine and fill it with clean water up to the maximum
level. After filling the water, the cleaning process will start au-
tomatically, and the « » icon will be flashing.
F. When the coffee machine prompts you to add clean water, the
« » icon will flash on the display.
Once the system cleaning is finished, you will hear two short
sound signals and the coffee machine will automatically switch to
the standby mode (fig. 5).
REGULAR MAINTENANCE OF THE COFFEE MACHINE
Removal/installation of main parts of the coffee machine
Figure 19 illustrates the specifics of removing/installing the main
parts of the coffee machine.
Warning: when reinstalling the brewing unit (13) in the correct
position, you will hear a characteristic clicking sound of the lock.
If you can't hear it, remove the brewing unit again and reinstall
it. (When installing the brewing unit (13), align the ledges at the
base of the brewing unit with the corresponding slots in the cof-
fee machine, then slide it until you hear the characteristic click-
ing sound).
Warning: check if the water tank is at the same level as the top
surface of the coffee machine. If not, push on the water tank until
it fits into place completely.
Daily maintenance is important to ensure durability and excel-
lent taste.
Can be used with a professional tablet to
clean the brewing unit from coffee oils * –
Remove the brewing unit from the coffee
machine and place the cleaning tablet in the
ground coffee compartment, install the brew-
ing unit back to its place and prepare a large
cup of Espresso (set the maximum volume).
Then remove the brewing unit and clean any
residues manually.
It can be used with professional tablets/liquids
for cleaning milk residues.*
Other