Bort BDR-3000-RR Bedienungsanleitung Seite 10

14 . Scrub pad;
15 . Funnel;
16 . Measuring cup;
17 . Wide brush with polymer bristles;
18 . Point nozzle;
19 . Window nozzle;
20 . Small round brush with polymer bristles;
21 . Brush with metal bristles;
22 . Multi-functional brush .
THE COMPLETE SET INCLUDES:
1 . Bent spray nozzle;
2 . Spray nozzle for door/window;
3 . Small round brush with metal bristles;
4 . Small round brush with nylon bristles;
5 . Wide brush-nozzle with nylon bristles;
6 . Terry cloth (2);
7 . Aluminium tubes;
8 . Measuring cup;
9 . Nozzle floor brush .
Product Life:
The service life of the product is 5 years .
Production date:
Is indicated on the packaging of the goods .
Shelf life:
Shelf life is not limited (subject to storage conditions) .
Storage conditions:
Products are stored in dry, ventilated warehouses at tem-
peratures from 0 ° C to +40 ° C with a relative humidity of
not more than 80% .
Transportation:
It is strongly prohibited dropping and any mechanical
impact on the packaging during transportation .
When unloading / loading, it is not allowed to use any
type of equipment that works on the principle of pack-
ing clamping .
QUICK GUIDE
WARNING: Do not try to connect accessories
while unit is emitting steam .
ALUMINUM POLE
Continuing to press down the gray lock/release button
of the Main Nozzle, slide Aluminum Pole onto Main Noz-
zle (fig .3) until button snaps through hole on the pole .
MOP HEAD
Align Mop Head with end of Aluminum Pole, so that hole
in Mop Head neck aligns with gray lock/release button
on the pole . Press down on gray lock/release button .
While continuing to hold button down, slide Mop Head
neck onto Aluminum Pole . Press on firmly until button
snaps through hole (fig . 4) .
MICROFIBER PADS
1 . Lay on Microfiber Pad on flat surface, with two fastener
strips for facing upward;
2 . Align Mop Head above Microfiber Pad . Make sure Mop
Head is oriented with pad as shown, and centered as best
as possible (fig . 5-A);
3 . Fastener strips will adhere to pad grips on underside of
Mop Head . Microfiber Pad should now be attached and
ready for use (fig .E 5-B) .
CAUTION: Use care when handling a recently
used Microfiber Pad, as it may still be hot .
NOTE: Microfiber Pads are machine washable .
To avoid picking up lint, washing separately
from other fabrics is recommended . Only use
liquid detergent . Avoid using any fabric softeners or
bleach . Air drying is recommended .
IMPORTANT: Surfaces that are not properly sealed
may be warped or damaged by exposure to heat and
moisture. Care should also be taken when steaming
sealed hardwood floors, as prolonged exposure to
steam in a single spot may cause damage and dis-
coloration. To avoid this, keep the Mop Head in con-
stant motion on these surfaces. Steam may remove
the sheen from some floors that have been treated
with wax. Extremely rough textured floors may tear
or damage Microfiber Pads.
STEAM CLEANING ACCESSORIES
STEAM JET NOZZLE / SQUEEGEE / BRUSH / SCRUB PAD
1 . Select Steam Jet Nozzle and align rear end of accessory
with Main Nozzle . The hole in Steam Jet Nozzle should
align with gray lock/release button on Main Nozzle;
2 . Press down on gray lock/release button (fig . 6) . While
continuing to hold button down, slide Jet nozzle onto
Main Nozzle(FIGURE 6) .Push it over button, and continue
pushing until button snaps through the hole .
UTILITY BRUSHES
NOTE: Utility Brushes connect to the Steam Jet
Nozzle, not the Main Nozzle .
1 . Align guide tab on inside of Utility Brush (FIGURE 7)
with groove in bottom of Steam Jet Nozzle tip;
2 . Firmly press Utility Brush onto tip of Steam Jet Nozzle .
Press it on as far as possible to prevent steam leakage .
SQUEEGEE
NOTE:Squeegee connects to the Steam Jet
Nozzle, not the Main Nozzle .
1 . Place Squeegee over tip of Steam Jet . Nozzle, and firm-
10