two trees TTS Pro Bedienungsanleitung Seite 8

REFERENCE OF MATERIALS
For engraving ：
TTS 5.5Pro
Material
Speed (mm/min)
Plywood 1500
Acrylic 1500
Leather 3000
Electroplated coating 300
Powder coating 1500
Anodic alumina 1500
Stainless steel 1000
MDF 1500
Peddle 1500
Plastic sheet 1500
Cardboard 1500
For Cutting ：
TTS 5.5Pro
Material
Speed (mm/min)
Plywood 1mm 200
Plywood 2mm 100
Plywood 3mm 100
Plywood 4mm 100
Plywood 5mm 100
Plywood 6mm 100
Plywood 7-8mm 100
Acrylic 1mm 100
Acrylic 3mm 100
Acrylic 6mm 100
Note:
The energy value is set to 500, and the laser intensity accounts for 50% of the power.
The energy value is set to 1000, and the proportion of laser intensity to power is 100%. The larger the energy, the
faster the speed can be set.
The above parameters only for reference. Due to the different properties of the materials, please adjust the parameter
values according to the actual situations.
11
TTS 5.5Pro TTS 10Pro TTS 10Pro
Power (%) Speed (mm/min) Power (%)
20 3000 40
20 3000 40
10 6000 10
100 500 100
100 3000 100
80 3000 40
100 1500 100
60 3000 60
100 3000 100
40 3000 40
50 3000 50
TTS 10Pro
TTS 10Pro
TTS 5.5Pro
Power (%)
Speed (mm/min)
Times Times
100
1 1
150
1 1
150
2-3 1-2
150
2-3 1-2
150
2-3 3
150
3-4 2-3
150
3—4 2—3
150
1 1
150
2-3 1-2
150
3-5 2-3
ADJUST THE FOCUS
TTS-55 PRO
5.5W Blow air block fixed
focus introduction
Times
1
1
1
1
1
1
1
1
1
1
1
100
Focus adjustment before engraving:
100
Before engraving, the focus need to be adjusted. The focus needs to be on the surface of the engraved object. It can
use a fixed-focus column for auxiliary adjustment. Place the fixed-focus column between the engraved object and the
100
adjustment block, and rotate the Z-axis lifting module to make the laser module stick on the 1st steps of the fixed
focus column.
100
Focus adjustment before cutting:
Before cutting, the focus needs to be in the middle of the fault of the engraved object, so according to different plate
100
thicknesses, the corresponding focus should be set, and the Z-axis lifting module should be rotated to adjust.
Assuming the object is 2mm, use the 2nd step of the fixed focus column;
100
The object is 4mm, using the 3rd step of the fixed focus column;
The object is 6mm, using the 4th step of the fixed focus column.
100
100
100
100
TWO TREES
Sculpt objects
Laser module
Blow air block
Fixed-length column
Shading block
Object
Fixed-length column
(Be careful of damage to the laser hood by impact)
Laser
module
2.00
Engraving
uses the 1 step The thickness of the engraved object
EN
"Engraving" uses the 1 step
"Cutting 2mm" uses the 2 step
"Cutting 4mm" uses the 3 step
"Cutting 6mm" uses the 4 step
Laser
module
TWO TREES
Sculpt objects
Cutting
is 2mm Adopt the second step
12