Upkeep And Maintenance - Mhz R 03 Betriebsanleitung

ROLLER BLIND R_03 R_04 R_05 with electric motor
Operation Manual
7. Operation
DE
Hazards caused by the operation of a defective product!
The operation of a non-compliant product can lead to injuries to people or
If you notice anything unusual happening or any unusual noises during
operation, immediately stop using the product and contact the responsible
Operation of the product is dependent on the control elements that are being
used with it (electrically powered versions only).
Typical controls for this purpose are buttons or wireless transmitters with
self-explanatory symbols that enable intuitive operation.
Operation as per the control elements' documentation and/or
as instructed by the fi tter installing the product.
FR
During operation, do not reach into product openings!
When operating the roller blind manually, its movement must be monitored.
When it is being operated automatically, it must be ensured as far as possible
that there are no people or objects in the products' path of travel.
Do not apply any loads to the product, no not lean any objects up against the
Do not pull on the product, do not try to hold the product!
8. Disruption and defect identifi cation
8.1 Identify the defect
Operation of the roller blind is not possible.
8.2 Repair
• The battery is not suffi ciently charged (versions with battery-powered radio-controlled drive
only)
⇒ Using the charger, charge the battery.
• The power supply has been lost (versions with mains power connection only)
EN
⇒ Check the fuses and, if necessary, fl ip the fuse.
• The drive unit has become overloaded/overheated (electrically powered versions only)
⇒ Prior to trying to start the drive again, let it cool down for 15 minutes.
• The blind has got caught, jammed or gone askew at the side.
⇒ Rectifi cation/replacement by specialist fi rm.
8.3 Service address
The service address is as shown in the information in Section 1.2 'Manufacturer'.

9. Upkeep and Maintenance

Regular maintenance constitutes part of using the roller blind properly and is an absolute
prerequisite for its effi cient and safe operation.
Hazard through the use of unsuitable materials and techniques!
Any repairs to the roller blind may be carried out only by trained personnel
that have been instructed in the prevailing safety and accident prevention
The roller blind must not be opened - it does not contain any parts that the
Turn off the electricity and fuses prior to performing repair work
(versions with mains connection only).
Repairs and upkeep/maintenance work that is not performed accordingly will
result in the loss of conformity with the 2006/42/EC Directive!
9.1 Service address
The service address is as shown in the information in Section 1.2 'Manufacturer'.
9.2 Spare parts and consumable supplies
Using original spare parts and only consumables approved by the manufacturer constitutes part
of using the product properly.
9.3 Inspection and maintenance work, maintenance intervals
9.3.1 Routine upkeep work
• Clean blind fabric: follow cleaning and care instructions in the 'Textiles Information' brochure.
• Check all connections and mechanical assemblies for wear and tear and integrity.
22
CAUTION!
animals and/or to damage!
specialist fi rm.
CAUTION!
CAUTION!
Hazard through improper operation!
product!
WARNING!
regulations.
layman could repair.
10. Taking the blind down
10.1 Special safety precautions for removing the blind
WARNING!
Hazard through the use of unsuitable materials and techniques!
Work on electrical systems or equipment may only be performed by qualifi ed
electricians or other appropriately instructed persons under the supervision
of an electrician and must be performed in accordance with all electrical
regulations (versions with mains connection only).
The roller blind may be taken down only by experienced specialist fi rms/
fi tters.
As it is being removed, the blind must be secured against falling down.
10.1.1 Description of the removal process
• Switch off power supply (versions with mains connection only)
• Check that blind has no power (versions with mains connection only)
• By pulling the Hirschmann coupling, disconnect cable connection (versions with mains
connection only)
• Take down the roller blind as per the installation instructions.
• Throughout the complete process of removing it, secure the roller blind from falling down!
CAUTION!
Hazard through falling!
Any people or animals present could be injured by the roller blind or parts of
it falling down!
When loosening the fi xings, ensure that the roller blind is always adequately
secured.
Danger of falling from ladders!
If the blind is fi tted in a high position, a secure ladder must be used! Only use
the ladder on an even and load-bearing surface! Pay attention to the maximum
load-bearing weight!
The ladder must not be leaned up against the product!
If the ladder is not properly set up or loaded, it can fall over!
10.2 Disposal/Recycling
ATTENTION!
Risk of environmental pollution / wasting resources!
Materials are to be separated according to material groups
and recycled accordingly!
Separate collection of electric and electronic components
as per the 2002/96/EG Directive!
Observe local recycling regulations!
Edition 06.2024
Subject to technical changes I