MHZ R 03 Betriebsanleitung Seite 21

Roller blind R_05
1 Alu bracket
3 Tube with fabric
4.2 Functional description
The products are installed for decorative or light management purposes on or around windows.
The movement of some products is electrically powered. The product is automatically stopped
at the top and bottom end of its path of travel. Factory staff programme the end positions on the
product in its delivery condition (electrically powered versions only).
R_04 also has set end positions when operated manually.
4.3 Safety Concept
The products are intrinsically safe and following correct installation can be safely used by the
operator until normal wear ends their service life.
The electrically powered drive system is of a size and design that when used properly there are
adequate safeguards against any risks to humans or animals (electrically powered versions only).
4.4 Notes on the battery-operated radio-controlled drive unit
• Protect products / radio-controlled drive unit from knocks during transportation, storage and
installation.
• Use only the charger approved by MHZ!
• The rechargeable battery is shipped partially charged.
• Prior to fi rst use, the battery must be fully charged (takes c. 6 hours).
• In subsequent operation, the time required to charge the battery when fully discharged is c.
3 hours.
• In order to preserve the battery's charge capacity, it should be recharged every 6 months.
• The red LED on the charger lights up when the charger is plugged in and indicates the charg-
ing activity. As soon as the green LED comes on, the battery is fully charged.
• Number of movement cycles per battery charge: c. 300, depending on product weight and
size (1 movement cycle equates to one up and down movement).
• Battery and radio-controlled drive unit are fi tted as a single item inside the product housing.
Defective batteries cannot be replaced alone.
• Remote control range in enclosed buildings: c. 35 m.
• The setting of the end positions is retained even when the battery has discharged.
• Radio-controlled drive and control system components are not compatible with other manu-
facturers' products.
• Minimum drive system distance from radio equipment: 20 cm.
4.5 Notes on the electric drive unit with mains connection
• Any suitable roller blind switch can be installed as the control element.
Determining its technical suitability and installing the switch are tasks that must be done by an
electrician!
4.6 Operator stations
Not relevant.
Edition 06.2024
Subject to technical changes I
2 Cable
4 Weighted rod, inlying
ROLLER BLIND R_03 R_04 R_05 with electric motor
5. Transport, storage and set-up conditions
5.1 Special safety precautions for transport
CAUTION!
Risk of injury through uncontrolled load movement!
Protect product from slipping or tipping over during all loading and
transportation.
Do not store or set product down upright.
5.2 Local requirements
5.2.1 Ambient conditions
The products must be installed only in dry surroundings that can be heated, and not in any
explosive atmospheres. The degree of electromagnetic compatibility of the electrically powered
products conforms to Directive 2014/30/EU in terms both of resistance to and emission of any
interference. These products must not be used in surroundings with higher than normal levels of
interference or that contain highly sensitive equipment!
6. Installation and fi rst entry into service
6.1 Installation
WARNING!
Hazard through the use of unsuitable materials and techniques!
The products may be installed only by experienced specialist fi rms/fi tters.
During installation, the product must be secured against falling down.
The product must be installed only in dry internal rooms. Any penetration of
moisture must be avoided!
6.1.1 Unpacking instructions
• All packaging parts are to be opened, loosened and removed carefully, so that the equipment
is not damaged.
• Take care that the product is not knocked or dropped!
• Remove group packaging, cardboard, foils and transport aids and separate according to the
material groups and recycle or dispose of in an environmentally compatible way in accordance
with local regulations.
CAUTION!
Danger of falling from ladders!
If the product is being fi tted in a high position, a secure ladder must be used!
Only use the ladder on an even and load-bearing surface! Pay attention to the
maximum load-bearing weight!
The ladder must not be leaned up against the product!
If the ladder is not properly set up or loaded, it can fall over!
6.1.2 Installation work description
• Bring the product to room temperature before assembly.
• The product is fi xed to the ceiling or wall or fi tted within a recess.
• The installer must independently assess the composition of the substrate and select the appro-
priately sized fasteners (screws, dowels etc.).
• Check the selected drill hole locations with a detector to ensure that there are no electrical
conduits!
• Align and fi rmly fi t the prescribed number of support brackets to wall/ceiling/recess.
• Fit the roller blind as per the installation instructions.
• During installation protect the motor cable from getting damaged (versions with mains
connection only).
• Check that the motor cable has been laid safely and with no damage (versions with mains
connection only).
• Check that the roller blind is fi rmly attached to wall/ceiling/recess.
6.2 Connections (versions with mains connection only)
CAUTION!
Danger of tripping through incorrect installation!
All of the product's supply or connecting lines must run along side walls or
ceiling.
6.2.1 Electrics connection (versions with mains connection only)
WARNING!
Hazard through electrical shock due to incorrect installation!
The installation of any 230-volt components without a mains plug must be
done only by an electrician or a duly instructed person under the guidance and
supervision of an electrician and must be done in accordance with all electrical
regulations.
The power supply may be turned on only after complete installation and the
closing of all covers!
All lines and materials used must suit the intended purpose in every aspect of
their specifi cation.
• Plug mains cable with device and mains plug into mains socket
• The installation of any 230-volt components without a mains plug must be done only by an
electrician.
6.3 First entry into service
CAUTION!
The roller blind is commissioned by the specialist fi rm at the operating
company's premises. The product is handed over in full working order.
The specialist fi rm will instruct the operator during commissioning in how the
product works, how it is operated and on the safety precautions.
Operation Manual
21
DE
FR
EN