Specifi Cations - Hameg HM8131-2 Handbuch

15 MHz Arbitrary Function Generator HM8131-2
Valid at 23 °C after a 30 minute warm-up period
Frequency specifications
Range: 100 μHz to 15 MHz
Resolution: 100 μHz; 100 mHz (sweep mode)
Display: ‹ 10 ms (without band change)
‹ 60 ms (with band change)
Accuracy: ±(10 ppm x freq.+ 30 μHz)
HM8125 (ext. reference frequency): ± 30 μHz
Temperature coefficient: 2 ppm/°C
Ageing: 10 ppm/year
Waveforms
Sine wave
Frequency range: 100 μHz to 15 MHz
Amplitude: 0 – 20 V
Distortion: 10 Hz to 20 kHz:
20 kHz–3 MHz:
3 MHz–15 MHz:
Nonharmonic
distortions: 100 μHz–1 MHz:
1 MHz–15 MHz:
Phase noise: ‹ -90 dBc / √Hz (0 dBm, 1 kHz from carrier)
Rectangle
Frequency range: 10 μHz to 15 MHz
Amplitude: 0 – 20 V
Rise/fall time: ‹ 10 ns
Overshoot: ‹ 5 % (U
Symmetry: 50 % ±(5 %+10 ns)
Ramp
Frequency range: 100 μHz to 100 kHz
Amplitude: 0 - 20 V
Linearity: better than 1 % (‹ 100 kHz)
Polarity: positive/negative
Rise/fall time: 45 ns
Triangle
Frequency range: 100 μHz to 1 MHz
Amplitude: 0-20 V
Linearity: better than 1 % (‹ 100 kHz)
Noise
White noise: Bandwidth 10 MHz
Pink noise: Bandwidth 100 kHz
Arbitrary
Frequency range: 100 μHz to 10 MHz
Amplitude: max. 20 V
Output rate: 40 MSa/s
Resolution: 12 bit (amplitude)
Filter: Bessel, 7
Memories: 1x 4 K-words not volatile
1x 16 K-words volatile
Jitter: ‹ 25 ns
Inputs
Gate/trigger
Impedance: 5 kΩ II 100 pF (protected to 30 V)
Amplitude modulation
Impedance: 1 kΩ (protected to ±30 V)
External reference
Frequency: 10 MHz ± 2 ppm
Input voltage: 1 V
rms
Impedance: 500 Ω (protected to ±30 V)
Outputs
Signal output BNC socket, short-circuit-proof
ext. voltage max. ±15 V f. 30 s.
Impedance: 50 Ω
Output voltage: Range 1:
Range 2:
Range 3:
1
Resolution: 3 / digit (100 / 10 / 1 mV)
2
Display of V
(except in arbitrary mode)
Setting accuracy: Sine wave 1 kHz: ±(1% x amplitude + 5 digits)
Rectangle 1 kHz: ±(3 % x amplitude + 5 digits)
(open circuit)
pp
‹ 0.1 %
‹ 1 %
‹ 3 %
‹ -65 dBc
‹ -(65 dBc + 6 dBc/Octave)
(open circuit)
pp
≤ 200 mV)
out
(open circuit)
pp
(open circuit)
pp
(open circuit)
pp
th
order, b=10 MHz
2.1 – 20 V (open circuit)
pp
0.21 – 2.0 V (open circuit)
pp
20 – 200 mV (open circuit)
pp
or RMS
pp
Frequency response: ‹100 kHz:
100 kHz – 1 MHz: ±0.3 dB
1 MHz – 15 MHz: +0.5 dB
Temperature stability: ± 0.1 % /°C
Trigger output BNC socket, short-circuit proof
Level: 5V / TTL level
Ramp output
Voltage progression: 0–5 V; synchronous with sweep
Impedance: 1 kΩ
DC offset
Output voltage: Range 1:
Range 2:
Range 3:
Resolution: 3 digit
Accuracy: ±(1 % x offset voltage + 5 digits)
Temperature stability: ± 0.1% /°C
Phase
Range: 0 – 359.9°
Resolution: 0.1°
Reference: declining slope of the synch. signal
Jitter: ‹ 25 ns
Accuracy: except for rectangle: ± (0.1+ freq./ Hz x 10
for rectangle: ± (5 + freq./ Hz x 30 x 10
Sweep (internal)
Internal sweep: all waveforms, linear or log.
Ranges: 100 mHz to max. signal frequency
selectable beginning and end frequencies
Sweep time: from 10 ms to 40 s, continuous or triggered
(ext. signal, front panel keypad, interface)
Modulation
FSK/PSK: all signals
Frequency range: 100 μHz to max. frequency
Triggering: by external signal
Minimum duration: 25 μs
Delay: PSK:
FSK:
Amplitude modulation
Modulation source: internal or external
Modulation depth: 0 to 100 %
Bandwidth: DC – 20 kHz (-3 dB)
Carrier frequency: 100 μHz to max. signal frequency
Accuracy: ± (5 % of reading + 2 %)
Internal modulation: 1 kHz sine wave
External modulation: 20 Hz – 20 kHz
Gate: (asynchronous)
Delay time: ‹150 ns
Input signal: TTL
Trigger function: (synchronous)
Frequency range: ‹ 500 kHz
Burst mode via ext. trigger or interface
Miscellaneous
Optional memory card: PCMCIA II format up to 1 MB
for storage of up to 16 ARB signals
Memories: 10 for device settings;
1 for ARB signal storage
Interface: RS-232 (standard), IEEE-488 (optional),
USB (optional)
Safety class: Safety Class I (EN 61010-1)
Supply voltage: 115 / 230 V ± 10 %, 50 / 60 Hz
Power consumption: approx. 30 VA
Operating temperature: +10 °C to + 40 °C
Max. relative humidity: 10 %–90 % (without condensation)
Dimensions (W x H x D): 285 x 75 x 365 mm
Weight: approx. 5 kg
Accessories supplied: Operator's Manual, power cable, Software (for RS-232)
Optional accessories: HZ33/HZ34 Test Cable 50 Ω (BNC-BNC), HO831 Memory
Card 1 MB, HZ10S/R Silicone test lead, HZ20 Adapter plug, HO870 USB
Interface, HO880 IEEE-488 (GPIB) Interface
S p e c i f i c a t i o n s
±0.2 dB
-5 V... + 5 V (open circuit)
-0.5 V... + 0.5 V (open circuit)
-50 mV + 50 mV (open circuit)
-6 ) degrees
-6 ) degrees
typ.10 μs
typ. 15 μs
Subject to change without notice
39