Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Spraying a burst of steam
1. Set the thermostat dial A
r
2. Set the steam selector A
4
3. Press the burst button A
2
Wait at least 5 seconds between bursts of steam.
4
Do not use the steam burst button for more than 5 consecutive
4
seconds.
Hold the product vertical and use bursts of steam to remove
4
creases from hanging fabric.
Spraying a spray of steam
Press the spray button A
3
to spray steam.
After use
1. Set the thermostat dial A
r
2. Place the product on the back cover A
3. Unplug the power cable A
1
Troubleshooting
Problem
Possible cause
The product doesn't
The thermostat
produce heat.
dial A
r
to OFF.
The product is not
plugged in.
The burst of steam
The burst of steam
doesn't function.
function has been
used to often.
The water reservoir
A
is empty.
6
The ironing plate
The thermostat dial
A
A
8
leaks water.
r
is out of the
steam range.
The product has not
fully heated up yet.
The amount of
water exceeds the
MAX indicator of
the water reservoir
A
.
6
The product doesn't
Set the steam
selector A
produce enough
steam.
The steam holes
A
9
are blocked.
The water reservoir
A
6
is empty.
The spray nozzle
There is not enough
A
7
doesn't spray.
pressure or air inside
of the product.
to the second or third position.
to the maximum position.
to spray a burst of steam.
to the minimum position.
w
.
from the power outlet.
Possible solution
Set the thermostat
is rotated
dial A
r
to the
correct setting for
your fabric.
Plug the power
cable A
into a
1
power outlet.
Continue ironing in
horizontal position
and wait a while
before using the
burst of steam
function again.
Fill the water
reservoir A
6
distilled water.
Set the thermostat
dial A
r
to the third
position.
Wait until the LED
indicator A
e
switches off to
indicate the product
is heated up.
Pour out the excess
water from the
water reservoir A
Set the steam
selector A
4
to 0.
4
to
the desired steam
output.
Clean the steam
holes A
9
with
distilled water.
Fill the water
reservoir A
6
distilled water.
1. Push the spray
nozzle A
7
hand.
2. Push the spray
button A
3
multiple times.
Cleaning the product
-
Disconnect the product before cleaning.
-
Before cleaning and maintenance, switch off the product and
disconnect the power. Let the product cool down completely.
-
Do not use aggressive chemical cleaning agents such as
ammonia, acid or acetone when cleaning the product.
-
Do not clean the inside of the product.
-
Disconnect the product from the power source before service
and when replacing parts.
1. Clean the product regularly with a soft, clean, dry cloth. Avoid
abrasives that can damage the surface.
2. Clean the ironing plate A
abrasive cleaner.
3. Clean the ironing plate A
fiber is stuck to the ironing plate A
4. Remove any limescale from the steam holes A
toothpick.
5. Empty the water reservoir A
To remove all water from the water reservoir A
4
connect the product to a power outlet and set the thermostat
dial A
r
to the maximum position for two minutes.
The built-in anti-scale cartridge reduces the build-up of limescale.
4
The built-in anti-scale cartridge does not stop the natural process
of limescale build-up.
Self-cleaning function
Use the self-cleaning function once every two weeks.
Use distilled water.
4
1. Fill the measuring cup A
2. Open the water reservoir cover A
3. Empty the measuring cup A
4. Close the water reservoir cover A
5. Place the product on the back cover A
6. Plug the power cable A
7. Set the thermostat dial A
with
Wait until the LED indicator A
is heated up.
8. Unplug the power cable A
9. Hold the product horizontally above the sink.
10. Press and hold the self-cleaning button A
reservoir A
6
Boiling water and steam ejects to remove the impurities from the
steam holes A
9
11. Plug the power cable A
12. Iron an old piece of cloth to dry the ironing plate A
13. Unplug the power cable A
6
.
Disposal
The product is designated for separate collection at
an appropriate collection point. Do not dispose of the
product with household waste.
For more information, contact the retailer or the local
authority responsible for the waste management.
c
Kurzanleitung
Dampfbügeleisen
with
Weitere Informationen finden Sie in der erweiterten
Anleitung online: ned.is/iron2000
by
Bestimmungsgemäße Verwendung
Dieses Produkt ist ein Dampfbügeleisen, das für eine breite Auswahl
von Stoffen verwendet werden kann.
Dieses Produkt ist mit einem Tropfschutzsystem ausgestattet, das
verhindert, dass Wasser aus der Bügelsohle austritt, wenn das
Produkt kalt ist.
5
8
with a damp cloth and a non-
8
with a damp cloth with vinegar if
8
.
6
.
y
with water.
5
.
y
into the water reservoir A
5
.
w
.
1
into a power outlet.
to the maximum position.
r
e
switches off to indicate the product
1
from the power outlet.
t
is empty.
.
1
into a power outlet.
from the power outlet.
1
9
with a
6
and product,
6
.
until the water
8
.
IRON2000
Werbung
