Hellberg Local 446 Gebrauchsanweisung Seite 10

The battery pack/headset will charge when connected to
a USB power supply. Only use a charger that is approved
to local directives for electronic devices. Use the USB
charge cable supplied with the headset. Check that the
charge cable is correctly connected to the charging socket
(A8). The batteries must be inserted prior to inserting the
charge cable.
Power supply specifications: Output DC 5V 1000 mA
(Limited Power Source – LPS).
When charging, the LED (A11) will flash green. When the
batteries are fully charged, the LED changes to solid green.
LED will flash green with high frequency if there is an error
detected when charging.
Disconnect the charger cable when batteries are fully
charged.
Important!
When use AA battery pack only use included NiMh
re-chargeable batteries or with similar performance.
Never use batteries with more than 1,5volt.
Never leave the battery pack/headset unattended when
charging.
Do not use the headset when the batteries are charging.
Only use a power supply and cable as specified by the
manufacturer.
Only charge the batteries at room temperature (10-25°C,
(50-77°F)).
Do not disassemble, crush or expose the batteries to
extreme heat or fire.
If storing the unit for a longer time remove the batteries from
the battery pack.
If these instructions are followed, the product is unlikely to
present any hazards within the meaning of EN 60950-1.
Parts (pic. A)
A1: Thermoplastic headband
A2: Thermoplastic helmet attachment
A3: Replaceable foam liner
A4: Replaceable foam filled plastic ear cushions
A5: Replaceable foam filled head cushion
A6: Boom microphone
A7: Level-dependent microphones
A8: Charging socket
A9: Socket for boom-microphone
A10: Display
A11: LED
A12: Volume DOWN and decrease setting
A13: Volume UP and increase setting
A14: On/Off button
A15: Level dependent button
A16: PTT button
A17: Battery pack
A18: Battery pack thumb screw
A19: Bluetooth button
®
Accessories and spare parts
Hygiene kit: 99403-001
Sweat absorbers: 99900-001
Windshield boom microphone: 16999-001
USB charging cable Local: 39927-001
Boom microphone: 16982-001
Windshield level dependent microphones: 1059-001
Spare headband electronic: 26046-915
Spare helmet arm (pair): 26108-910
Battery pack Li-Ion Local 446: 17018-001
Battery pack Li-Ion Local 2: 17018-011
Battery pack AA Local 446: 17004-001
Battery pack gasket: 17112-001
Charger EU: 17193-001
Charger UK: 17193-007
Change the hygiene kit (pic. D)
• Remove the old foam liner (A3) and insert the new
• Pull off the old ear cushion (A4)
• Centre the new ear cushion over the hole
• Press with a finger along the outside of the ear cushion
until it attaches all around the edges
•Pull off the old head cushion (A5) and insert the new
Approval and technical data (E)
E:1) Headband
E:2) Helmet mounted
E:3) Tested and certified to (standards)
E:4) Weight
E:5) Mean attenuation
E:6) Standard deviation
E:7) Assumed Protection Value
E:8) Tested by (notified body)
E:9) Headband force
E:10) Size: S M L
E:11) Additional technical data
E:12) Radio channel frequencies
E:13) Sub tone channel frequencies
Approved helmet combinations
These earmuffs attached to head protection and/or face
protection devices shall be fitted to, and used only with,
the carriers(s)
listed in table G.
G:1) Manufacturer
G:2) Model
G:3) Adapter
Earmuffs complying with EN 352-3 are of medium size
range or small size range or large size range. Medium
size range earmuffs will fit the majority of wearers. Small
size range or large size range earmuffs are designed to
fit wearers for whom medium size range earmuffs are not
suitable.
Hereby, Hellberg Safety AB declares that the hearing
protectors Local 446 and Local 2 are in compliance with
PPE regulation EU 2016/425 and the RED Directive
2014/53/EU.
The full text of the EU declaration of conformity is available
at: www.hellbergsafety.com/declaration-of-conformity
For manufacturing date, see the date clock on the inside
of the ear cup. Expected lifetime of product, excluding its
batteries, is 5 years. Serial number is placed on label on the
bottom of the ear cup.
This product is covered by the Waste Electrical and
Electronic Equipment Directive (WEEE) 2012/19/EU.
Do not dispose of your product as unsorted municipal
waste. Batteries must be disposed of in accordance
with national regulations. Use local recycling system for
electronic products.
10