Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Other
fluids
may damage
your
Cab light:
locomotive.
ve and replace the bulb.
Attention!
Never
touch
the
hea-
Replacing the smoke generator
ting element in the center of the
2
smoke generator.
It is fragile.
- Pull the safety cover out of the
smoke stack (Fig. 3).
Power Supply
- ull the smokebox
Attention!
For safety and reliabi-
boiler (Fig. 4).
Iity, operate
this model with LGB
- Unplug
power
supplies
(transformers,
smoke generator from the circuit
power packs and controls) only.
board
The use of non-LGB
power sup-
- Push the old generator out of
plies will void your warranty.
the smokestack.
Use this model with LGB power
- Push the replacement
supplies with an output of at least
into the stack and plug the wires
1 amp. For more information on
into the loco circuit
LGB
power
supplies
for indoor,
- Reassemble.
outdoor
and multi-train
operation,
see the LGB catalog.
Replacing the traction tire 2
- Use a small, straight-blade
Attention!
After extended
opera-
ewdriver
tion, this model may leave carbon
tire out of the wheel groove.
dust
or
other
debris
around
the
- Use a small, straight-blade
track. This debris can stain carpet
ewdriver to gently pry the new
and other
materials.
Consider
this
traction tire into the wheel groo-
when setting up your layout. Ernst
Paul
Lehmann
Patentwerk
and
ve.
- Make
LGB
of America
are not liable
for
seated properly in the wheel
any damages.
groove.
Replacing the motor 3
SERVICE
- Remove the two small (3 mm)
hex
Do-ft-yourself
Service
Levels
Level 1 - Beginner
gear just
Level
2 - Intermediate
boards
These
Level
3 - Advanced
gear with the locomotive body.
Attention!
Improper
service
will
- Remove
void your warranty. For quality
bottom of the gearbox.
service,
contact
your
authorized
- Remove
retailer or an LGB factory service
bottom of the steam chest/cylin-
station (see Authorized
Servi-
der molding.
ce).
- Pull the gearbox assembly out of
Lubrication
1
the loco (Fig. 6). Disconnect the
The
drive
rod
ends
should
be
four-wire connecting cable.
lubricated
occasionally
with
a
- Remove
small
amount
of LGB
Maintenan-
top of the gearbox.
ce Oil (50019).
- Replace
Cleaning
I
ble.
This
model
can
be cleaned
exter-
Attention!
nally using a mild detergent and
ved,
gentle stream of water. Do not
gears
immerse
this
model.
(51020).
Replacing
the light
bulbs
I
Attention!
Front
lower
lanterns:
Pull
the
drive rods do not bind. Binding
lantern housing away from the
can cause serious damage to the
model.
Remove
and replace
the
model.
bulb.
Reassemble.
Replacing
Front upper
and rear lower
lan-
shoes
terns:
Remove
the ring around
- Remove
the lantern lens. Carefully pry the
bottom of the gearbox
lens away from the lantern. Using
- Remove the bottom of the gear-
tweezers,
remove and replace the
box.
bulb.
Reassemble.
- Remove
Rear
upper
lantern:
Carefully
the side
pull the wires down to remove the
themselves.
light socket
from the lantern.
- Replace
Replace the bulb. Reassemble.
shoes
8
Using tweezers,
remo-
front out of the
the
wires
for the
old
inside
the
boiler.
generator
board.
scr-
to pry the old traction
scr-
sure
that
the
traction
tire
is
head
screws
on
the
valve
below the running
on both
sides
of the
loco.
screws
connect
the
valve
the
rear
screw
on
the
the two screws
on the
the two screws
on the
the
motor.
Reassem-
If the
motor
is remo-
generously
lubricate
the
with LGB
Gear
Lubricant
Make
sure
that
the
the brushes,
pick-up
or wheelsets
3
the
six screws
on the
(Fig. 6).
the
6
mm
screws
on
rods and
the side
rods
the wheelsets,
pick-up
or brushes.
Reassemble.
Werbung
