Werbung
Verfügbare Sprachen
Verfügbare Sprachen
ENGLISH
GENERAL INDICATIONS
1
We thank you for buying the SWR DX wheels, product that will gua-
rantee you security and functionality through the years.
Before proceeding with using the wheels, please read carefully the
following instruction and store them in a safe place for eventually
reusing. Fac Michelin S.r.l. reserve to modify the content of this
manual without notice. The updated version will always be avai-
lable www.miche.it
On our website you will also find information on the other Miche or
SWR products and the spare parts catalogue.
In the box of wheel set you will find:
• The front wheel arranged with TX-12 system
• The rear wheel arranged with TX-12 system
• Wheel bag
• The manual of instructions and use of wheels
• Rim tapes
• Vibrostop
Warning
!
Any modification or alteration (and graphic) of the product with
non-original spare parts or spare parts not delivered directly
by Fac Michelin S.r.l., involves the expiration of the guarantee.
Warning
!
Direct and violent impacts on broken road surfaces can cause
damage to the rims. Such damage is outside the conditions of
our guarantee and repair costs will be charged directly to the
customer.
Warning
!
In case of strange impact caused from bad road base or wheels
transport, we trust to bring the wheels to your mechanic for a
check.
Warning
!
Only Shimano original lock ring designed for through axle inter-
nal diameter 27mm to be used with the disc brake.
Warning before using the bicycle:
• Check for proper operation and state of wear of all the compo-
nents before starting to ride.
• Check the condition and pressure of the tyres fitted to your Mi-
che wheels. Pressure must not exceed the limit of 8 bar and
116 psi signed behind valve hole. The inflating pressure of the
tyres must NOT exceed the LOWER pressure level between the
maximum pressure stated by the tyre manufacturer.
Excessive tire pressure reduces the grip of the tire on the road
and increases the risk that the tire will unexpectedly burst.
Inflation pressure that is too low reduces tire performance and
increases the probability of sudden and unexpected loss of tire
pressure. In addition, premature damage to the rim may occur.
Incorrect
tire pressure could cause tire failure or loss of control of the
bicycle, resulting in an accident, personal injury or death.
• Check that the wheels are firmly anchored to the frame with
the locking item closed in the correct position (Fig. 7-8). If there
is the passing through pin, consult the installation instructions
provided by the manufacturer of the bicycle or fork.
Attention, an incorrect locking may cause the detachment of the
wheel and derive in accidents and serious or fatal injuries.
• Check the tension of the spokes so as to notice any spokes
which got loose. In the case spokes are loose, contact a qua-
lified mechanic or special personnel to perform the tensioning.
Attention, the use of wheels not centered properly or with spo-
kes broken and/or loosen or damaged may cause an accident,
serious injury or death.
• Check that the braking system and the brake pads in the brake
calipers are in good state and that the screws on the disc or the
locking ring of the disc, depending on your model, are properly
locked.
• To the users of more than 85kg weight, Fac Michelin S.r.l. sug-
gests to check the wheels status to the mechanic every two
months or every 1,500km.
• We reccomend using these wheels if you weigh more than
102 Kg
• Never wash the pieces with pressure-fed water because water
may get through the seals and cause permanent damage to the
internal components. We recommend washing components with
a sponge, mild soap, and water.
• Salt water environments (as found on winter roads and neat the
seaside) can cause galvanic corrosion on most bike parts. Care-
fully rinse, clean, dry and re-lubricate all exposed parts to avoid
damage, malfunctions and accidents.
• If your component shows signs of rust, this means it has to
be changed urgently as it might be a sign of damage.
HUBS
2
Warning
!
If you have any doubt whatsoever your service-repair ability,
please take your bicycle to a qualified repair shop.
Before any maintenance operations on your wheels, always
wear gloves and protection glasses.
Use original spare parts exclusively provided by
Fac Michelin S.r.l.
When replacing any broken sealed bearings please ensure sealed
bearing correct measure and specification are used.
Rear hub
Right side
26x17x5 (6803)
Left side
26x17x5 (6803)
The SWR DX hubs are easy to maintain. To do it, proceed as
follows:
FRONT HUB
The front hub does not require any particular maintenance. For any
extraordinary maintenance and replacement of bearings, follow
these simple steps.
• Extract the cage chamber (B) including the nuts (Fig. 1)
Front hub
26x17x5 (6803)
26x17x5 (6803)
5
Werbung
