Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Lighting
other
This model has automatic
directional
dust and debris can stain carpet and
lanterns on the front and the rear of
other materials.
the loco: three white lanterns on the
setting up your layout. Ernst Paul
front
and two
red lanterns
on the
Lehmann
rear. The control panels inside the
America are not liable for any dam-
cabs are equipped with white lights
ages.
for background lighting along with
small LEDs. Several LEDs are illumi-
nated in the front cab. One is illumi-
SERVICE
nated in the rear.
This model has "flat' multi-purpose
Do-it-yourself
sockets, with removable covers, on
Level n - Beginner
the front and rear of the loco. These
Level
sockets can be usedto provide track
Level
power to cars with lighting or sound
electronics.
Attention! Improper service will void
To remove the cover of the socket,
your warranty. For quality service,
pull it straight out. If the cover is
contact your authorizedretaileror an
tight, gently use a small straight
LGB factory service station (see
screwdriverto pry it out. (Do not pull
Authorized Service).
out the rectangularouter housing.)
Hint: Additional expert instructions
Catenary Power Operation
for many LGB products are available
This locomotivecan be operatedwith
at www.lgb.com.
a powered catenary system (see
Operating Modes). The bottom of
Lubrication n
this model is marked with a red dot.
Theaxle bearingsshould be lubricat-
Place the model on the track with the
ed occasionally with a small amount
red dot pointing to the rail that is not
of LGBMaintenanceOil (50019).
connected to the catenary power
supply (Fig. 5/6).
Cleaning n
Hint: To operate multiple trains on
This model can be cleaned externally
the same track, we recommend the
using a mild detergent and gentle
LGB Multi-Train System (see Multi-
stream of water. Do not immerse this
Train System). With the Multi-Train
model.
System, you can use an unpowered
catenary system for prototypical
Attention! This model is equipped
with
appearance.
exposethe speakerdirectly to water.
CAUTION!This model may be pow-
ered with a catenary on analog lay-
Replacing the light bulbs n
outs only. For operationwith the dig-
Lanterns: Carefullypry the lens away
ital Multi-Train System, the model
from the lantern. Using tweezers,
must use track power. Otherwise,
remove and
dangerously high voltages may
Reassemble.
result.
Cab light: Using tweezers, remove
and replace the bulb.
Attention! After extended operation,
this model may leavecarbon dust or
16
debris around
the track. This
Maintenance parts
Consider
this when
50010 Smokeand CleaningFluid
50019 Maintenance
Patentwerk
and
LGB of
51020 Gear Lubricant
62201 Standard Motor with Short
63120 Brushes, Assembled,
63218 StandardPick-Up Shoes,
Service Levels
68511 Plug-in Bulb, Clear,5 V,
- Intermediate
- Advanced
68512 Plug-in Bulb, Red, 5V,
69104 Traction Tire, 37.5 mm,
INSTRUCTIONS
USERS
MTS Onboard
Programming functions
You can program numerous func-
tions of the onboard decoder to suit
your requirements. If you want to do
this, program the "function values"
in "registers" (CVS) using a PC and
the
Programming Module. You can also
program the function values using a
55015 Universal Remote.
Hints:
- For normal operation, it is not nec-
sound
electronics.
Do
not
essary to change the function val-
ues.
- If programming results in unsatis-
factory operation, you can repro-
gram the factory pre-set values of
most important CVs: Program reg-
replace the bulb.
ister
This also reprograms the loco
address to the factory pre-set
value.
To reprogram the factory pre-set
function values with the 55015 (dis-
plays shows "P --") input 6, 5, and 5
and pressthe right arrow button.The
display shows "P -
Oil
5, and 5 and press the right arrow
button again.
Shaft
14 mm and 16 mm, 8 pieces
(2 packagesneeded)
2 pieces(2 packages needed)
10 pieces
10 pieces
10 pieces
FOR ADVANCED
Decoder
55045
MTS
PC
Decoder
CV55 to function
value
55.
again: Input 5,
17
Werbung
