Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
2.
TECHNICAL DESCRIPTION
The La Nordica combi stoves are suitable for heating living spaces for some periods. Logs of wood or pellets are used
as fuel. Following careful studies it has been possible to use two different fuels, as in this case wood and pellets, in a
unique stove.
IMPORTANT: the simultaneous use of both types of fuel mentioned above is not envisioned!
For easiness, from now on we will talk about the components listed below, with reference to chapter 19.
The following chapters explain how to switch the stove over for use with wood and for the use with pellets.
The stove is built from galvanised and painted sheet steel, cast iron (hearth grate (G) and grate support), details in
majolica. The hearth is lined internally by individual cast iron and refractory sheets (IRONKER). Inside, find a burner
(B chap.) and a burner cap (CB) in thick, easy-to-remove cast iron.
The combustion chamber unit is hermetically sealed by welding and is covered with a painted steel sump. The
replaceable internal deflectors (DF), reflect the radiation of the fire and increase the temperature inside the
combustion chamber further. In this way, combustion is optimised and the level of efficiency is increased by taking
advantage of the flow of exhaust gases.
The ceramic glass in the door is a unique piece (resistant up to 700° C), and allows an enchanting view of the burning
flames, while preventing the escape of sparks and smoke. Under the pellet burner (B) there is a removable drawer for
collecting the ash, which is accessible from door Picture 1 pos.A. Most of the ash produced by the combustion of
wood remains inside the burner caps (CB).
The environment is heated by:
radiation : the heat is irradiated into the room through the panoramic glass and the external hot surfaces of the
stove.
The stove is supplied with a register for regulation of the air necessary for combustion and several apertures (non-
adjustable) for the pre-calibrated air.
Air register (R) (Picture 1)
The air regulation knob is found under the hearth door on the left.
The wood storage box must be opened to access the knob (C).
Use this register to regulate the passage of air that enters the lower
part of the stove and through relevant ducts is conveyed in direction
of the fuel. The primary air is necessary for the combustion process
in the lighting phase. The ash drawer must be emptied regularly so
that the ash cannot obstruct the entry of primary air.
Turn the knob clockwise (to the right) to increase the passage of
primary air.
WOOD functioning - The air passage must be open only slightly
during combustion of wood, otherwise the wood burns too
quickly and the stove overheats. (see paragraph 10).
Functioning with PELLETS - When lighting has taken place, the
user can adjust the heating power through the air register (R)
from the minimum power (register partially closed) to the
maximum power (register completely open).
3.
INSTALLATION REGULATIONS
The stove is assembled and ready for connection and must be connected via a fitting to the existing flue in the home.
The fitting must be short, straight, horizontal and positioned slightly in ascent. The connections must be waterproof. It
is mandatory to respect national and European Standards local provisions or on the subject of building
legislation, as well as fire/prevention regulations. We therefore recommend that you collect information previously
from your local chimney sweep.
It is also necessary to check the sufficient flow of air required for combustion. Regarding this, it is fundamental to pay
attention to windows and doors with sealed closure (gaskets)
It is prohibited to connect several appliances to the same chimney. The diameter of the aperture of the flue for
connection must correspond more or less with the diameter of the combustion gas pipe (fitting).
The aperture must be supplied with a wall connection for the receipt of the exhaust pipe and a wall plate. Before
installation, check that the capacity of the sub-structure supports the weight of your appliance. If the capacity is
insufficient, it is necessary to take appropriate measures (e.g. plate for the distribution of the weight).
La NORDICA S.p.A. is not responsible for products modified without authorisation and for the use of non-
original spare parts.
THE HEARTHS MUST NOT BE MODIFIED.
22
A
R
C
8192000 Rev.04 – EN
CLEO COMBI
Picture 1
Werbung
Inhaltsverzeichnis
