Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Center gear post (7)
Idle arm (6)
Holder center
post assembly
Idle
up'down lever (5)
Insert the arm of the idle up/down
lever into the idle arm groove.
Fig. 6-34-2
1-6-35. Holder Center Post Assembly
Replacement
1. Tum over the mechanical deck and remove the center
gear pulley and the idle arm. (Refer to item "1-6-34.
Idle Arm Assembly Replacement".)
ind
. Tum over the mechanical deck and remove the top
bracket and the cassette holder assembly. (Refer to
item "1-6-1. Top Bracket Assembly Replacement and
1-6-2, Cassette Holder Assembly Replacement".)
3. Remove the drive arm assembly. (Refer to item "1-6-
5. Drive Arm Assembly Replacement".)
4. After removing two screws (1), replace the holder
center post assembly (2).
5. After replacing. mount the parts in the reverse order of
removal.
Screw (1)
post assembly (2)
Apply a few
drops of oil.
Projection
Fig. 6-35-1
2-30
Note:
+
When mounting, push the cutout (A) on the holder
center post assembly (2) aligning with the projection
on the mechanical deck.
+ Screw tightening torque is 294 - 392 mNem (3 ~4
kgecm).
« Before mounting the center gear pulley, apply a few
drops of oil. (Refer to Fig. 6-34-1.)
1-6-36. REC Inhibiting Lever Replacement
1, Remove the top bracket. (Refer to item "1-6-1. Top
Bracket Replacement".)
2. Remove the cassette holder assembly. (Refer to item
"1-6-2. Cassette Holder Assembly Replacement".)
3. Remove the cam slider. (Refer to item "1-6-41, Cam
Slider Replacement".)
4. Remove the tension spring (2).
5. Undo the claw (A) on the S soft brake (1) sliding and
lifting it upward.
6. Remove the projection (B) on the REC inhibiting
lever (3) sliding in the direction shown by the arrow
and lifting it upward.
7. After replacing the REC inhibiting lever (3), mount
the parts in the reverse order of removal.
Tension spring (2)
S soft
brake (1)
REC-inhibiting
lever (3)
Projection (B) -
Fig. 6-36-1
1-6-37. S, T Main Brake Assembly Replacement
1. Remove the mechanical deck from the main PC board
and turn the mechanical deck upside down.
2. When replacing the T main brake assembly (2), first
remove the idle kick lever (3). (Refer to item "1-6-34.
Idle Arm Assembly Replacement".)
3. Remove the tension spring (4).
4, Remove the claws on the S, T main brakes (1), (2)
from the mechanical deck lifting the S, T main brakes
(1), (2) upward.
5. After replacing the S. T Main brake assemblies (1),
(2), mount the parts in the reverse order of removal.
Note:
« When mounting the S, T main brake assemblies (1),
(2) take care that both ends of the S, T main brakes
(1), (2), do not touch the gear of the reel table.
idie kick lever (3)
Tension
spring (4)
S main brake (1)
Fig. 6-37-1
2-31
1-6-38. S Soft Brake Replacement
1.
Remove
the cam slider. (Refer to item "1-6-41. Cam
Slider Replacement.")
2. Remove the drive arm assembly. (Refer to item "1-6-
5. Drive Arm Assembly Replacement".)
3. Remove the S soft brake spring (1).
4. Remove the S soft brake (2) after removing the claw
(A) on the S soft brake from the mechanical deck.
Note:
« When mounting the S soft brake spring (1). take care
not to deform the hook (B).
* When mounting the S soft brake (2), take care of the
band brake (3).
S soft brake spring (1)
S$ reel tabie
assembly
REC- inhibiting
fever
'Band
brake (3)
Hook
Fig. 6-38-1
Werbung
