Werbung
Verfügbare Sprachen
Verfügbare Sprachen
1-6-25. Loading Slider Assembly Replacement
1. Remove the mechanical deck from the main PC board.
Set the mechanical position to the F/L out position.
.
Tum over the mechanical deck.
. Remove the stop ring (1).
Mk
Wh
Remove the loading slider assembly (2) while lifting
its tip upward using the mold portion on the loading
slider assembly (2) as a fulcrum.
6. Mount the parts in the reverse order of removal.
Note:
* When mounting the loading slider assembly (2), insert
the tip of the loading slider assembly (2) slightly to the
mold portion, then mount it so that the claw on the
outsert is in the position of the cutout portion of the
loading slider assembly.
Confirm that the position mark on the loading slider
assembly (2) and the mark on the T loading gear
match each other in position.
Mold portion
Loading slider assembly (2)
Mechanism deck bottom side
Fig. 6-25-1 View from Mechanica! deck bottom side
T loading gear
Loading Sider asseminty (2)
Fig. 6-25-2
1-6-26. Hook Lever Assembly Replacement
1. Remove the top bracket. (Refer to item "1-6-1. Top
Bracket Replacement".
2.
Remove the cassette holder assembly. (Refer to item
"1-6-2. Cassette Holder Replacement".)
3. Remove the drive arm assembly. (Refer to item "1-6-
5. Drive Arm Assembly Replacement".)
4. Remove the tension spring (1).
5. Turn the hook fever assembly (2) counterclockwise
slightly, and remove the claw on the hook lever
assembly (2) then teplace.
6. After replacing the hook lever assembly (2) , insert the
(A) portion of the hook lever under the S reel table
assembly. When the portions (B), (C), (D) are in line,
push the claw into the mechanical deck.
Tension spring (1)
Claw
(A)
o.
S reel table
assembly
Hook lever
assembly (2)
Cam slider
Fig. 6-26-1
7. Tum the hook lever assembly (2) clockwise till it
stops, and mount the tension spring (1). After replac-
ing the hook lever assembly (2), slide the cam slider in
the direction shown by the arrow, and then position
the boss (E) under the cam slider.
Tension
Hook lever (2)
spring (1)
S reel table
assembly
Fig. 6-26-2
1-6-27. Hook Replacement
1. Remove the hook lever assembly. 'Refer to item "1-6-
26. Hook Lever Assembly Replacement".)
2. Tur over the hook lever assembly (1) and remove the
hook lever assembly (1) opening the portion (A) of the
hook (2) slightly and lifting the hook (2) upward.
3. When mounting a new hook, push the hook (2) in the
portion (B) from above.
Note:
* Take care not to confuse the mounting direction of the
hook (2).
Portion (A)
Hook lever
assembly (1)
Fig. 6-27-1
1-6-28. Tension Drive Lever Replacement
1. Remove the cam slider. (Refer to item "1-6-41. Cam
Slider Replacement".)
2. Tum over the mechanical deck and remove the tension
drive lever (1) from the projection (A) moving
counterclockwise slightly.
3. After replacing the tension drive lever (1) , mount in
the reverse order of removal.
Note:
* For the cam slider mounting, refer to the notes in item
1-6-41.
Mechanical deck
{Bottom side)
Projection (A)
Tension
drive lever (1)
Fig. 6-28-1
1-6-29. Loading Drive Assembly Replacement
1. Remove the F/L ground plate and the head cleaner
assembly. (Refer to item "!-6-14. Head Cleaner
Assembly Replacement".)
tw
. Remove two flat cables (1) from the connectors.
3. Pull out the portion (A) (No. 8 guide cap) from the
motor bracket (2).
4. Remove four claws (a), (b), (c), (d) securing the motor
bracket in the order of (a) — (b) > (c) > (d).
Flat cable (1)
FL ground plate
Claw (a)
Claw (b)
Portion (A)
(No.8 guide cap)
Motor bracket cay
Claw (d)
Fig. 6-29-1
Note:
+ Remove the claw (a) inserting a driver.
* Remove the claws (b) and (c) pushing inside previ-
ously and opening the claws slightly.
Claw
ei
Fig. 6-29-2
Werbung
