Kärcher FRV 50 ME Bedienungsanleitung Seite 7

,
)
You
пееd
to
use the matching high ргеs-
sчrе nozzles
to
епsчrе
that
уочr high рrеs-
sчrе сlеапеr wогks рrореrlу.
Note:
The rеqчirеd packets
of
nozzles
have Ьееп
adjusted
to suit
the
соrrеsропdiпg
high
рrеssчrе сlеапеrs
and must thеrеfоrе Ье
оrdеrеd separately.
Figчrе
1,
see cover page
1
Nozzle size
(example)
Read
the
nozzle size
frоm
the
type
plate
of the high-pressure сlеапеr.
Select
the
nozzle package
that
is suita-
ble
fоr
the high-pressure сlеапеr
frоm
the
following table.
Figure
2,
see cover page
't
О
riпg
2
Rotation аrm
3
Nozzle
4
Union joint
)
lпsеrthе
О
riпg
in
the nut
of
the rotation
аrm.
)
Place
the
nozzle
оп
it..
i
Slightlyfasten
the
nozzle
with
the
Union
joint.
Note:
The
exit
jet must
Ье
directed
раrаllеltо
the
rotation
аrm.
Figure
3,
see сочеr page
Ф
Adjust
the
wrепсh
аrеа
of
the
nozzle
(width
10) so that
it
is para|lel
to
the
rо-
tation
аrm.
)
Tighten the Uпiоп joint
(width 22) using
а
wrепсh.
)
Repeat the
рrосеss
оп
the
sесопd
rоtа-
Jion аrm.
Note:
Do
not
attach the nozzles
fоr
the
sчrfасе
сlеапеr
to
the sрrау
lапсе
of
the high-pres-
sчге сlеапеr.
Figure
4,
see cover page
1
lпjесtоr nozz|e
2
Wгепсh
)
Sсrеw
the injector
nozzle
into
the injec-
tor using
the
wгепсh and tighten
it
fin-'
gertight (8
Nm).
The wrепсh is included
with
the
nozzle
set.
Figure
5,
see cover page
1
Тriggег gun with control knob
2
Тriggеr gun without сопtrоl knob
З
Nipple, short
4
Nipple, long
lп
delivery condition, the short nipple is
in-
stal|ed оп the
device
for use оп
а
triggеr
gun
with а сопtrоl knob.
Fоr use
with а triggеr gun without
а
сопtrоl
knob, the shогt nipple must Ье чпsсrеwеd
and герlасеd
Ьу
the
enclosed
long nipple.
Grease
the О-riпgs
of
the nipple Ьеfоrе
in-
stallation.
Figчrе
6,
see cover page
)
Соппесt
the triggеr gun
of
the high-
рrеssчrе
сlеапеr
to
the
surface
сlеапеr
and hand-tighten
it.
Tighten using
а
wrепсh (27 mm)
if
needed.
^
слUтлоN
А
strong wastewater
jet
will
еmеrgе
frоm
ffie
hose
соппесtiоп. Do поt
чsе
ffie
sur-
face сIеапеr
withouf
а hose.
Figure
7,
зее cover page
)
Grеаsе
the О-гiпg
at
the end
of
the
hose
using the
accompanying grease
рriог to
installation.
ь
ЦlqEillýisЁ-a::!
п,ч#iglЁ.ФОi
Ёsё::i;;::iii:i:lii;i:];
)з6...040
2.642-431.0
2х10 +
20
)41...045 2.642-432.0
2х11
+
23
]46...050
2.642-433.0
2х12
+
26
]51...080
z.642-982.0
2х20
+
40
]81...100 z.64з-769.0
zхз0
+
40
101...125
2,64з-768.0
2х38 +
50
EN-2