Scheppach DH8000x Originalbetriebsanleitung Seite 20

1. Introduction
Manufacturer:
Scheppach GmbH
Günzburger Straße 69
D-89335 Ichenhausen
Dear customer,
We hope you have a lot of fun and success using your
new machine.
Note:
According to the applicable product liability laws, the
manufacturer of the device does not assume liability
for damages to the product or damages caused by
the product that occurs due to:
• improper handling,
• noncompliance of the operating instructions,
• repairs by third parties, not by authorized service
technicians,
• installation and replacement of non-original spare
parts,
• non-intended use,
• A breakdown of the electrical system that occurs
due to the non-compliance of the electric regu-
lations and VDE regulations 0100, DIN 57113 /
VDE0113.
We recommend:
that you read through the entire operating instruc-
tions before putting the machine into operation.
These operating instructions are to assist you in get-
ting to know your machine and utilize its proper ap-
plications. The operating instructions contain impor-
tant notes on how you work with the machine safely,
expertly, and economically, and how you can avoid
hazards, save repair costs, reduce downtime and in-
crease the reliability and service life of the machine.
In addition to the safety requirements contained in
these operating instructions, you must be careful to
observe your country's applicable regulations.
The operating instructions must always be near the
machine. Put them in a plastic folder to protect them
from dirt and humidity. They must be read by every
operator before beginning work and observed con-
scientiously. Only persons who have been trained in
the use of the machine and have been informed of
the various dangers may work with the machine. The
required minimum age must be observed. In addition
to the safety requirements in these operating instruc-
tions and your country's applicable regulations, you
should observe the generally recognized technical
rules concerning the operation of identically con-
structed devices.
We accept no liability for accidents or damage that
occur due to a failure to observe this manual and the
safety instructions.
20 | GB
2. Device description (Fig. 1-3)
1. Handle
2. Air inlet
3. Cover flap
4. Support legs
5. Wheels
6. Water pipe
7. Handle
8. Display
a. De-humidifying operation
b. Automatic defrosting
c. Speed display
d. Operating hours counter
e. Set speed
f. Decrease target humidity
g. Increase target
h. On/Off switch
i. Humidity display
j. Level indicator
3. Scope of delivery
A. 2x Wheels
B. 1x Wheels axle
C. 1x Handle
D. 8x Self-tapping screw
E. 4x Hexagon head screw M6x35mm
F. 2x Hexagon head screw M6x30mm
G. 1x Building dryer
H. 2x Cotter pin
I. 2x Support legs
4. Intended use
The device is designed for applications operated with
a 230 V alternating current source. Be sure to ob-
serve the restrictions in the safety instructions.
This air dehumidifier is only designed for indoor use
to dry moist walls damage caused by water or to re-
duce the air humidity in confined spaces bigger than
10.1 m².
The intended usage also includes compliance with the
operating, servicing and repair conditions prescribed
by the manufacturer and following the safety instruc-
tions included in the instructions. Follow the relevant
accident prevention rules for operation and other gen-
erally recognised health and safety at work rules.
The machine is to be used only for its prescribed
purpose. Any other use is deemed to be a case of
misuse. The user / operator and not the manufacturer
will be liable for any damage or injuries of any kind
caused as a result of this. Please note that our equip-
ment has not been designed for use in commercial,
trade or industrial applications. Our warranty will be
voided if the equipment is used in commercial, trade
or industrial businesses or for equivalent purposes.
www.scheppach.com