Introduction; Device Description; Scope Of Delivery; Intended Use - Scheppach DH6500i Originalbetriebsanleitung

1. Introduction

Manufacturer:
scheppach
Fabrikation von Holzbearbeitungsmaschinen GmbH
Günzburger Straße 69
D-89335 Ichenhausen
Dear customer,
We hope you have a lot of fun and success using your
new machine.
Note:
According to the applicable product liability laws, the
manufacturer of the device does not assume liability
for damages to the product or damages caused by
the product that occurs due to:
• improper handling,
• noncompliance of the operating instructions,
• repairs by third parties, not by authorized service
technicians,
• installation and replacement of non-original spare
parts,
• non-intended use,
• A breakdown of the electrical system that occurs
due to the non-compliance of the electric regu-
lations and VDE regulations 0100, DIN 57113 /
VDE0113.
We recommend:
that you read through the entire operating instruc-
tions before putting the machine into operation.
These operating instructions are to assist you in get-
ting to know your machine and utilize its proper ap-
plications. The operating instructions contain impor-
tant notes on how you work with the machine safely,
expertly, and economically, and how you can avoid
hazards, save repair costs, reduce downtime and in-
crease the reliability and service life of the machine.
In addition to the safety requirements contained in
these operating instructions, you must be careful to
observe your country's applicable regulations.
The operating instructions must always be near the
machine. Put them in a plastic folder to protect them
from dirt and humidity. They must be read by every
operator before beginning work and observed con-
scientiously. Only persons who have been trained in
the use of the machine and have been informed of
the various dangers may work with the machine. The
required minimum age must be observed. In addition
to the safety requirements in these operating instruc-
tions and your country's applicable regulations, you
should observe the generally recognized technical
rules concerning the operation of identically con-
structed devices.
16 І 36
 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58
2. Device description (Fig. 1-3)
1. Handle
2. Control Panel
3. Air Inlet grille
4. Wheels
5. Whater pipe bracket
6. Air Outlet Grille
7. Power Cordl
8. Water Pipe
A. Purge key
B. Humidity and Time Display
C. Time key
D. Operating Indicator
E. ON/OFF key
F. Defrosting Indicator
G. Up and Down key
H. Purging Indicator

3. Scope of delivery

1x - DH6500i
1x - Handle
1x - Manual
• Open the packaging and remove the device care-
fully.
• Remove the packaging material as well as the
packaging and transport bracing (if available)
• Check that the delivery is complete.
• Check the device and its spare parts for possible
damage caused by transportation. In the event of
complaints, you must contact the distributor with-
out delay. Claims at a later stage will not be ac-
cepted.
• If possible, store the packaging until the warranty
period has expired
m Attention!
The device and packaging materials are not toys!
Children must not be allowed to play with plastic
bags, film and small parts! There is a risk of swal-
lowing and suffocation!

4. Intended use

The device is designed for applications operated with
a 230 V alternating current source.
Be sure to observe the restrictions in the safety in-
structions.
This air dehumidifier is only designed for indoor use to
dry moist walls damage caused by water or to reduce
the air humidity in confined spaces.
The intended usage also includes compliance with the
operating, servicing and repair conditions prescribed by
the manufacturer and following the safety instructions
included in the instructions.
Follow the relevant accident prevention rules for opera-
tion and other generally recognised health and safety at
work rules.
The machine is to be used only for its prescribed