Makita DLM465 Betriebsanleitung Seite 14

Tips for maintaining maximum
battery life
1. Charge the battery cartridge before completely dis-
charged. Always stop tool operation and charge the
battery cartridge when you notice less tool power.
2. Never recharge a fully charged battery cartridge.
Overcharging shortens the battery service life.
Charge the battery cartridge with room tempera-
3.
ture at 10 °C - 40 °C (50 °F - 104 °F). Let a hot
battery cartridge cool down before charging it.
When not using the battery cartridge, remove
4.
it from the tool or the charger.
Charge the battery cartridge if you do not use
5.
it for a long period (more than six months).
ASSEMBLY
WARNING:
Always be sure that the lock key
and battery cartridge are removed before carrying
out any work on the mower. Failure to remove the
lock key and the battery cartridge may result in seri-
ous personal injury from accidental start-up.
WARNING:
Never start the mower unless it is
completely assembled. Operation of the machine
in a partially assembled state may result in serious
personal injury from accidental start-up.
Installing the handle
NOTICE:
When installing handles, position the
cords so that they are not caught by anything
between the handles. If the cord is damaged, the
mower switch may not work.
1. Align the holes in the lower handle with the holes
in the mower body, and then tighten 4 bolts temporarily.
► Fig.1: 1. Lower handle 2. Bolt
► Fig.2: 1. Holes for upper bolt
NOTE: The handle height can be adjusted in two
levels by replacing the upper bolt in either of the two
holes on each side of the mower body. For details,
refer to the section for adjusting the handle height.
2.
Firmly tighten 4 bolts which were temporarily
tightened in step 1 using box wrench 13.
3. Align the hole in the lower handle with the hole in
the upper handle, then insert the bolt from inside, and
then tighten the nut from outside with box wrench 13.
Perform the same procedure on the other side.
► Fig.3: 1. Bolt 2. Lower handle 3. Nut 4. Hole 5. Upper handle
CAUTION:
Hold the upper handle firmly so
that it does not drop off your hand. Otherwise, the
handle may fall and cause an injury.
4. Attach the holders to the handle.
Align the protrusions on the holder with the holes on the
handle so that the protrusions fit in the holes. Position
the cords as shown in the figure.
► Fig.4: 1. Cord 2. Holder
Removing the mulching plug
1. Open the rear cover.
► Fig.5: 1. Rear cover
2. Remove the mulching plug while holding down the
lever.
► Fig.6: 1. Lever 2. Mulching plug
Assembling the grass basket
1. Pick up the upper clip of the grass basket.
► Fig.7: 1. Upper clip
2.
Insert the frame into the grass basket as far as it
will go while holding the handle of the frame.
► Fig.8: 1. Handle
NOTICE:
Do not insert the handle into the grass
basket. Be sure to insert the frame along the stitch of
the grass basket.
3. Make sure that there is no sagging on the corners
of the grass basket.
► Fig.9
4.
Open the upper clip, and attach it to the frame.
► Fig.10
5. Attach all the other clips as shown in the figure.
Make sure that all the clips are securely attached to the
frame.
► Fig.11: 1. Clip
Installing or removing the grass
basket
To install the grass basket, follow the steps below.
1. Open the rear cover.
► Fig.12: 1. Rear cover
2. Hold the handle of the grass basket, and then
hook the grass basket on the rod of the mower body as
shown in the figure.
► Fig.13: 1. Rod 2. Handle 3. Grass basket
To remove the grass basket, open the rear cover, and
then remove the grass basket by holding the handle.
Attaching the mulching plug
1. Open the rear cover, and then remove the grass
basket.
► Fig.14: 1. Rear cover 2. Grass basket
2. Attach the mulching plug while holding down the
lever, and then release the lever to lock the mulching
plug.
► Fig.15: 1. Lever 2. Mulching plug
14 ENGLISH