Bosch GWS Professional HEAVY DUTY 18V-10 SC Originalbetriebsanleitung Seite 28

28 | English
Note: The coding cams on the protective guard (12) ensure
that only a protective guard that is suitable for the power
tool can be fitted.
Protective guard for cutting
Always use the protective guard for cutting (17) when
u
cutting bonded abrasives.
Provide sufficient dust extraction when cutting stone.
u
The protective guard for cutting (17) is fitted in the same
way as the protective guard for grinding (12).
Extraction guard for sanding
The extraction guard (11) can be used to minimise dust
when sanding paint, varnish and plastics in conjunction with
the carbide grinding head (16). The extraction guard (11) is
not suitable for working metals.
A suitable Bosch vacuum cleaner can be connected to the
extraction guard (11).
The extraction guard (11) is mounted in the same manner as
the protective guard (12). The brush collar can be replaced.
Extraction guard for cutting with a guide block
The extraction guard for cutting with a guide block (27) is fit-
ted in the same way as the protective guard for grinding
(12).
Side handle
Do not operate your power tool without the side
u
handle (10).
Do not continue to use the power tool if the auxiliary
u
handle is damaged. Do not make any alterations to the
auxiliary handle.
Screw the side handle (10) on the left or right of the ma-
chine head depending on how your are working.
Low-vibration auxiliary handle
ably.
Do not make any alterations of any kind to the auxili-
u
ary handle.
Do not continue to use a damaged auxiliary handle.
Hand guard
Always fit the hand guard (21) when working with the
u
rubber sanding plate (22) or with the cup brush/disc
brush/flap disc.
Attach the hand guard (21) to the side handle (10).
Fitting the abrasive tools
Remove the battery from the power tool before carry-
u
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
1 609 92A 6YN | (28.07.2021)
The low-vibration auxiliary
handle reduces vibration,
enabling the tool to be used
safely and more comfort-
Do not touch grinding and cutting discs until they have
u
cooled down. The discs can become very hot while work-
ing.
Clean the grinding spindle (20) and all the parts to be fitted.
Lock the grinding spindle with the spindle lock button (3)
before clamping and releasing the abrasive tools.
Do not press the spindle lock button while the grind-
u
ing spindle is moving. The power tool may become dam-
aged if you do this.
Grinding/Cutting Disc
Pay attention to the dimensions of the abrasive tools. The
diameter of the hole must match that of the hub flange. Do
not use an adapter or reducer.
When using diamond cutting discs, ensure that the arrow in-
dicating the direction of rotation on the diamond cutting disc
matches the direction of rotation of the power tool (see the
direction of rotation arrow on the machine head).
See the graphics page for fitting instructions.
Use the quick-clamping nut (15) to secure the grinding/cut-
ting disc without the need for additional tools.
Only use the quick-clamping nut (15) for grinding/cutting
discs up to a maximum diameter of 150 mm.
The quick-clamping nut (15) may be used only for
u
grinding or cutting discs.
Only use quick-clamping nuts (15) that are in good
u
working order and not damaged.
When screwing on, make sure that the printed side of
u
the quick-clamping nut (15) is not facing the grinding
disc.
Always secure a grinding/cutting disc using only the
u
quick-clamping nut (15) supplied.
Press the spindle lock but-
ton (3) to lock the grinding
spindle. To tighten the
quick-clamping nut (15),
fold up the bar and turn the
quick-clamping nut firmly
clockwise. Then fold down
the bar to secure the quick-
clamping nut. It is not suf-
ficient to tighten the disc
along the edge.
Bosch Power Tools