Makita UV001G Betriebsanleitung Seite 14

Installing or removing the grass basket
To install the grass basket, follow the steps below.
1. Open the rear cover.
► Fig.4: 1. Rear cover
2.
Hold the handle of the grass basket, and then install
the grass basket by inserting the rod of the grass basket
into the grooves on the machine as shown in the figure.
► Fig.5: 1. Grass basket 2. Handle 3. Rod
To remove the grass basket, open the rear cover, and
then remove the grass basket by holding the handle.
FUNCTIONAL DESCRIPTION
CAUTION:
Always be sure that the machine
is switched off and the battery cartridges are
removed before adjusting or checking function on
the machine.
Applications of scarifier blades
Vertical cutter
The vertical cutter removes the thatch and moss from
the lawns and cut the roots of lawns vertically. The verti-
cal cutter loosens the soil and increases the aeration of
lawns, and let the water go into the roots of lawns and
prevent the water from staying on the surface.
► Fig.6
Thatching blades
The thatching blades remove the thatch and mosses
from the lawns without cutting the roots of lawns.
► Fig.7
Installing or removing battery cartridge
CAUTION:
Always switch off the machine
before installing or removing of the battery
cartridge.
CAUTION:
Hold the machine and the battery
cartridge firmly when installing or removing bat-
tery cartridge. Failure to hold the machine and the
battery cartridge firmly may cause them to slip off
your hands and result in damage to the machine and
battery cartridge and a personal injury.
CAUTION:
Make sure that you lock the battery
cover before use. Otherwise, mud, dirt, or water may
cause damage to the product or the battery cartridge.
CAUTION:
Always install the battery cartridge
fully. If not, it may accidentally fall out of the machine,
causing injury to you or someone around you.
CAUTION:
Do not install the battery cartridge
forcibly. If the cartridge does not slide in easily, it is
not being inserted correctly.
CAUTION:
Hold the battery cover firmly when
installing or removing the battery cartridge.
To install the battery cartridge;
1. Pull up the locking lever, and then open the battery cover.
► Fig.8: 1. Battery cover 2. Locking lever
2.
Align the tongue on the battery cartridge with the
slot on the machine, and then slide the cartridge until it
locks in place with a little click.
► Fig.9: 1. Battery cartridge
3. Close the battery cover and push it until it is
latched with the locking lever.
To remove the battery cartridge;
1.
Pull up the locking lever and open the battery cover.
2. Pull out the battery cartridge from the machine
while sliding the button on the front of the cartridge.
3. Close the battery cover.
Machine / battery protection system
The machine is equipped with a machine/battery protec-
tion system. This system automatically cuts off power to
the motor to extend machine and battery life. The machine
will automatically stop during operation if the machine or
battery is placed under one of the following conditions:
Overload protection
When the battery is operated in a manner that causes
it to draw an abnormally high current, the machine
automatically stops and the main power lamp blinks in
green. In this situation, turn the machine off and stop
the application that caused the machine to become
overloaded. Then turn the machine on to restart.
Overheat protection
When the machine is overheated, the machine stops automati-
cally and the main power lamp lights up in red. In this case, let the
machine and batteries cool before turning the machine on again.
NOTE: When the battery is overheated, the main
power lamp blinks in red.
Overdischarge protection
When the battery capacity is not enough, the machine
stops automatically and the main power lamp blinks in
red. In this case, remove the battery from the machine
and charge the battery cartridges or change the battery
cartridges to fully charged ones.
Protections against other causes
Protection system is also designed for other causes that could
damage the machine and allows the machine to stop automati-
cally. Take all the following steps to clear the causes, when the
machine has been brought to a temporary halt or stop in operation.
1. Turn the machine off, and then turn it on again to restart.
2. Charge the battery(ies) or replace it/them with
recharged battery(ies).
3. Let the machine and battery(ies) cool down.
If no improvement can be found by restoring protection
system, then contact your local Makita Service Center.
NOTICE:
If the machine stops due to a cause
not described above, refer to the section for
troubleshooting.
14 ENGLISH