EINHELL TE-MS 18/8 Li Originalbetriebsanleitung Seite 25

stop rail (double miter cut).
•
Move the machine head (4) to its upper po-
sition.
•
Release the turntable (8) by slackening the
locking grip (10).
•
Use the handle (2) to adjust the turntable (8)
to the angle required (in this connection see
also section 6.5).
•
Retighten the locking grip (10) in order to se-
cure the turntable in place.
•
Release the clamping lever (12) and use the
handle (2) to tilt the machine head (4) to the
left until it coincides with the required angular
setting (in this connection see also section
6.6).
•
Retighten the clamping lever (12).
•
Cut as described in section 6.4.
6.8 Sawdust bag (Fig. 2)
The saw is equipped with a sawdust bag (14) for
sawdust and chips.
The sawdust bag (14) can be emptied by means
of a zipper at the bottom.
6.9 Changing the saw blade (Fig. 17)
•
Danger! Remove the rechargeable battery
before you replace the blade.
•
Wear work gloves to prevent injury when
changing the saw blade.
•
Swing the machine head upwards (4).
•
Press the saw shaft lock (13) with one hand
while positioning the hexagon key (20) on the
flange bolt (31) with the other hand. The saw
shaft lock (13) engages after no more than
one rotation.
•
Now, using a little more force, slacken the
flange screw (31) in the clockwise direction.
•
Turn the flange screw (31) right out and remo-
ve the external flange (32).
•
Take the blade (5) off the inner flange and pull
out downwards. To do so, move the saw blade
guard (6) upwards to enable access to the
saw blade.
•
Carefully clean the flange screw (31), outer
flange (32) and inner flange.
•
Fit and fasten the new saw blade (5) in rever-
se order.
•
Important! The cutting angle of the teeth,
in other words the direction of rotation of the
saw blade (5) must coincide with the direction
of the arrow on the housing.
•
Check to make sure that all safety devices
are properly mounted and in good working
condition before you begin working with the
saw again.
Anl_TE-MS_18-8_Li_SPK13.indb 25 Anl_TE-MS_18-8_Li_SPK13.indb 25
GB
•
Warning! Every time that you change the
saw blade, check that the saw blade guard
(6) opens and closes again in accordance
with requirements. Also check that the saw
blade (5) spins freely in the saw blade guard
(6).
•
Warning! Every time that you change the
saw blade, check to see that it spins freely in
the table insert (23) in both perpendicular and
45° angle settings.
•
Warning! You should replace the table insert
(23) immediately whenever it is worn or da-
maged. To do so, undo the Philips screws in
the table insert (23) and take the table insert
out of the fixed saw table (9). To fit the new
table insert (23), proceed in reverse order.
•
Warning! The work to change and align the
saw blade (5) must be carried out correctly.
7. Cleaning, maintenance and
ordering of spare parts
Danger!
Always pull out the battery pack before starting
any cleaning work.
7.1 Cleaning
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it with compressed air at low
pressure.
•
We recommend that you clean the device im-
mediately each time you have finished using
it.
•
Clean the equipment regularly with a moist
cloth and some soft soap. Do not use
cleaning agents or solvents; these could at-
tack the plastic parts of the equipment. Ensu-
re that no water can seep into the device. The
ingress of water into an electric tool increases
the risk of an electric shock.
7.2 Carbon brushes
In case of excessive sparking, have the carbon
brushes checked only by a qualifi ed electrician.
Important! The carbon brushes should not be
replaced by anyone but a qualifi ed electrician.
7.3 Maintenance
There are no parts inside the equipment which
require additional maintenance.
- 25 -
18.10.2023 13:08:27 18.10.2023 13:08:27