EINHELL TE-MS 18/8 Li Originalbetriebsanleitung Seite 20

Danger!
When using the equipment, a few safety pre-
cautions must be observed to avoid injuries and
damage. Please read the complete operating
instructions and safety regulations with due care.
Keep this manual in a safe place, so that the in-
formation is available at all times. If you give the
equipment to any other person, hand over these
operating instructions and safety regulations as
well. We cannot accept any liability for damage
or accidents which arise due to a failure to follow
these instructions and the safety instructions.
Explanation of the symbols used (see Fig. 19)
1. Danger! - Read the operating instructions to
reduce the risk of injury
2. Caution! Wear ear-muff s. The impact of noi-
se can cause damage to hearing.
3. Caution! Wear a breathing mask. Dust
which is injurious to health can be generated
when working on wood and other materials.
Never use the device to work on any materi-
als containing asbestos!
4. Caution! Wear safety goggles. Sparks ge-
nerated during working or splinters, chips and
dust emitted by the device can cause loss of
sight.
5. Caution! Risk of injury! Do not reach into
the running saw blade.
6. Warning! To make miter cuts (with the saw
head inclined or the turntable set at an angle),
the adjustable stop rail must be fi xed at an
outer position.
To make 90° crosscuts, the adjustable stop
rail must be fi xed at the inner position.
7. Store the batteries only in dry rooms with an
ambient temperature of +10°C to +40°C.
Place only fully charged batteries in storage
(charged at least 40%). (Not supplied)
1. Safety regulations
The corresponding safety information can be
found in the enclosed booklet.
Warning!
Read all the safety information, instructions,
illustrations and technical data provided on
or with this power tool. Failure to adhere to the
following instructions may result in electric shock,
fi re and/or serious injury.
Keep all the safety information and instruc-
tions in a safe place for future use.
Anl_TE-MS_18-8_Li_SPK13.indb 20 Anl_TE-MS_18-8_Li_SPK13.indb 20
GB
Please note when reading the safety information
that this item of equipment does not have the fol-
lowing functions: carry-handle and laser.
2. Layout and items supplied
2.1 Layout (Fig. 1-17)
1. Release button
2. Handle
3. On/Off switch
4. Machine head
5. Saw blade
6. Adjustable blade guard
7. Fixed stop rail
8. Turntable
9. Fixed saw table
10. Locking grip for turntable
11. Pointer
12. Clamping lever
13. Saw shaft lock
14. Sawdust bag
15. Scale
16. Retaining pin
17. Scale (turntable)
18. Pointer (turntable)
19. Locking grip for adjustable stop rail
20. Hexagon key 6mm
21. Workpiece support
22. Clamping device
23. Table insert
24. Adjustable stop rail
25. Locking grip for workpiece supports
26. Adjustment screw for angle stop 90°
27. Adjustment screw for angle stop 45°
28. Lock nut
29. Adjustment screw for stop rail
30. Discharge opening
31. Flange bolt
32. Outer fl ange
33. Mount for battery pack
34. Battery (not included in delivery)
35. Charger (not included in delivery)
2.2 Items supplied
Please check that the article is complete as
specifi ed in the scope of delivery. If parts are
missing, please contact our service center or the
sales outlet where you made your purchase at
the latest within 5 working days after purchasing
the product and upon presentation of a valid bill
of purchase. Also, refer to the warranty table in
the service information at the end of the operating
instructions.
- 20 -
18.10.2023 13:08:25 18.10.2023 13:08:25