STEINEL True Presence COM1/ COM2/BT IPD UP Bedienungsanleitung Seite 10

First time of using True Presence
During initial commissioning, the pres-
ence detector creates a room image.
The room must be free of movement for
2 to 2.5 minutes for this.
The process is completed when the
white LED goes out.
Twilight setting
The chosen response threshold can be
set from approx. 2 to 2000 lux.
Setting True Presence detection
The reach can be set via the mounting
height, radius and scenario parameters.
Scenario 9:
Small office, quiet workplace
– This scenario features maximum sensi-
tivity. To prevent undesired switching, it
should be used for small areas.
Scenario 8:
Large office, quiet workplace
– As per scenario 9, but with a slightly
reduced sensitivity. Also suitable for
large areas.
Scenario 7:
Large office, large entrance area
– As per scenario 8, but with a further
reduced sensitivity.
Scenario 6:
Hotel room, room with persons sleeping
– This scenario also features maximum
sensitivity. In addition, signal process-
ing has been optimised to reliably de-
tect the presence of persons sleeping.
Scenario 5:
Hotel room, room with persons sleeping
– As per scenario 6, but with a further
reduced sensitivity.
Scenario 4:
Noisy workspace, light industry, hallways
– The sensor can be triggered by vibra-
tions. In scenarios 7-9, this may lead
to longer stay-ON times. Scenario 4 is
more robust in the way it works.
Scenario 3:
Noisy workspace, light industry, hallways
– As per scenario 4, but with a further
reduced sensitivity.
Scenario 2:
Very noisy environments, heavy industry
– This scenario should be used if there
are larger vibrations or if there are
sources of electrical interference.
The True Presence function is not
available, the sensor functions as a
conventional presence detector.
Scenario 1:
Very noisy environments, heavy industry
– As per scenario 2, but with a further
reduced sensitivity.
Setting Hallway detection
Reach can be set separately for each
direction.
Daytime operation
When movement is detected, the sensor
switches the load ON irrespective of
ambient brightness.
Teach-IN
The Teach-IN function is to be selected
at the level of light at which you want the
sensor to respond to movement from
now on. The level of ambient brightness
measured in this way will be saved after
10 seconds. The load is deactivated
during this period.
Time setting
The chosen stay-ON time can be set
from a minimum of 30 seconds (True
Presence)/10 seconds (Hallway) up to
a maximum of 60 minutes. When the
response threshold is exceeded, the
sensor switches OFF after the stay-ON
time expires.
- 18 -
Bluetooth grouping
The sensors can be operated a individual
sensor or as a group. The group is inter-
connected via wireless communication.
In each group, a group master must be
defined in the Smart Remote app. All
sensors in a group operate in the same
way as the group master is configured.
Reach can be set individually for all lights
in the lighting group.
Neighbouring-light function
The neighbouring-light function can be
activated and deactivated via the Smart
Remote app. This function assigns the
neighbouring groups to the active sensor
group. The active group responds to
activation signals from the neighbouring
group assigned to it and switches to
main light as defined in the settings.
Operating mode
Semi-automatic mode
The light now only switches OFF auto-
matically. Light is switched ON manually.
Light must be requested using the button
and stays ON for the time set.
Fully automatic mode
The light automatically switches ON and
OFF in relation to light level when some-
one is present. Light can be switched ON
and OFF manually at any time.
This temporarily interrupts the automatic
switching function.
Presentation mode
If input S is used in fully automatic mode
with load activated, the sensor will activate
presentation mode. The load remains
switched OFF as long as movement is
being detected. As soon as movement is no
longer being detected and the stay-ON time
has elapsed, the sensor returns to normal
sensor mode.
Button input
Tells the sensor how to interpret incoming
signal S. Assigning external buttons allows
you to operate the detector as a semi-auto-
matic unit and override it manually at any
time. SOUND or SOUND/OFF describes
the behaviour after actuating the button.
In the ON-OFF setting, the light can be
switched ON and OFF manually at any
time. In the SOUND setting, light can no
longer be switched OFF manually. The
stay-ON time starts from the beginning
again each time the switch is pressed.
IQ mode
The stay-ON time is self-learning and
adjusts dynamically to user behaviour.
The optimum time cycle is determined
by means of a learning algorithm. The
shortest time is 5 minutes, the longest
time 20 minutes.
Hallway pulse mode
The pulse function activates the output
for 2 seconds (e.g. for staircase lighting
time switches). The sensor will then be in
a dead time for 8 seconds.
Smart Remote app
To read off the sensor via smartphone or
tablet, you must download the STEINEL
Smart Remote app from your app store.
You will need a Bluetooth-capable smart-
phone or tablet.
Android
- 19 -