VOLTCRAFT PS-10 Bedienungsanleitung Seite 4

6 Controls
A. Rack for up to 8 mobile phones, smartphones or tablets
B. On/Off switch
C. Power LED
D. Round low-voltage socket for power supply
E. 6x USB current output, each with max. output current of 3 A
F. 2x USB current output with total output current of 3.6 A (combined)
G. 2x USB current output, each with output current of 2.4 A
7 Getting Started
Please note:
The USB charging station is only intended for charging appropriate equipment
(e.g. mobile phones, smartphones, tablets, etc.). It cannot be used as a USB hub
and does not transfer any data.
Connect the round socket (D) of the USB charging station with the corresponding round
plug of the enclosed power adapter. Connect the power adapter via the supplied mains
cable to an appropriate mains socket of the public supply grid.
Place the USB charging station on a level, flat, stable surface. Protect valuable furniture
surfaces by using a suitable mat to prevent scratches, pressure points or discolourations.
Switch on the USB charging station by the On/Off switch (B). The power LED (C) lights up.
The USB charging station is now ready for operation; the charging outputs can be used for
the connection of appropriate devices.
Please use a matching USB current output with your device. Four USB cables
(USB plug type A to USB-C connector) are in the package content, other USB
cables can be delivered as accessories.
As a rule, mobile phones and smartphones can be connected to the same current
output (E), as current output of 1 A should be sufficient for them.
In contrast, tablets should be connected to one of the two current outputs (G).
These outputs supply 2.4 A.
The two current outputs (F) share the output current of 3.6 A. Connect here either
two mobile phones/smartphones or one tablet. However, do not connect two tab-
lets.
Due to integrated electronics, the USB charging station detects the charging current re-
quired by a mobile phone, smartphone or tablet. However, due to great variety of devices
it cannot be guaranteed that all devices can be charged with maximum possible charging
current (as in case of an original charger matching the device).
After a mobile phone, smartphone or tablet is fully charged, disconnect it from the USB
charging station.
The USB charging station is protected against overtemperature, overcurrent and
short circuit. If the USB charging station does not operate correctly, disconnect it
from power supply. Also disconnect all connected devices from the charging sta-
tion. Wait until the charging station has cooled down. Eliminate the reason for the
failure (e.g. defect USB cable) and put the USB charging station again into use.
If charging of all connected devices is over, disconnect the USB charging station and switch
off the mains voltage by removing the mains plug out of the mains socket.
Keep the product in a cool, dry, dust-free place out of the reach of children.
8 Cleaning And Maintenance
The product does not require any maintenance and should never be disassembled for any
reason.
Disconnect the product from the mains voltage before cleaning.
Only clean the product with a soft, clean, dry cloth. Dust can easily be removed using a clean,
soft brush and a vacuum cleaner.
Never use aggressive cleaning agents or chemicals for cleaning; these can lead not only to
discolouration, but can also damage the product.
9 Disposal
This symbol must appear on any electrical and electronic equipment placed on the
EU market. This symbol indicates that this device should not be disposed of as
unsorted municipal waste at the end of its service life.
Owners of WEEE (Waste from Electrical and Electronic Equipment) shall dispose
of it separately from unsorted municipal waste. Spent batteries and accumulators,
which are not enclosed by the WEEE, as well as lamps that can be removed from
the WEEE in a non-destructive manner, must be removed by end users from the
WEEE in a non-destructive manner before it is handed over to a collection point.
Distributors of electrical and electronic equipment are legally obliged to provide free take-back
of waste. Conrad provides the following return options free of charge (more details on our
website):
in our Conrad offices
at the Conrad collection points
at the collection points of public waste management authorities or the collection points set
up by manufacturers or distributors within the meaning of the ElektroG
End users are responsible for deleting personal data from the WEEE to be disposed of.
It should be noted that different obligations about the return or recycling of WEEE may apply in
countries outside of Germany.
10 Technical Data
10.1 General
Ambient conditions ....................... Temperature 0 °C to +40 °C, air humidity 10% to 90% rela-
tive, not condensing
Operating location ........................ only in dry, enclosed indoor spaces
10.2 USB Charging Station
Operating voltage ......................... 21 V/DC
Charging outputs .......................... 10 (USB ports of type A and type C)
Output voltage .............................. 5 V/DC
Output current ............................... charging output 1, 2, 3, 4, 5, 6: max. 3 A each
charging output 7, 8: Combined 3.6 A
charging output 9, 10: max. 2.4 A each
Output current (combined) ............ max. 20.4 A
Dimensions (L x W x H) ................ 210 x 140 x 29.5 mm
Weight .......................................... 800 g
10.3 Power Supply Unit
Operating voltage ......................... 100 - 240 V/AC, 50/60 Hz
Output ........................................... 21 V/DC, 7.1 A
Protection class ............................ II
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com). All rights in-
cluding translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication
represents the technical status at the time of printing.
Copyright 2024 by Conrad Electronic SE. *2902798_v2_0224_02_dm_mh_EN