Werbung
Verfügbare Sprachen
Verfügbare Sprachen
PULLOUT
UT Lead Connections
@
fe ameiee terminals
@® Tape Deck terminais
|
t
|
Record (REC)
sording
(LINE
terminals
of a stereo
amplifier
with the connecting
lead sup-
plied (red tube).
eG (OL 02 merene Connect to the playback (PLAY)
terminais
of a stereo
amplifier
with
the connecting
fead sup-
|
olied (blue tube}.
a
DUTCIN laces paeeten Connect
to tne recording (REC)
oe
Connect to the recording
IN) terminals of a tape deck.
Connect
to the playback
(LINE
OUT) terminals of a tape deck.
Playback (PLAY)...
@ POWER switch
When
this switch
is depressed
(a), power is sup-
plied to the unit and the equalizer control LED indi-
cator lights up. The unit has a built-in muting circuit,
so that It begins to operate
normally about
3 se-
conds after power has been switched ON.
2) Eqaulizéer controls
The
audio
frequency
band
(20
Hz — 20
kHz)
is
divided into 10 bands, the controls providing a con-
tinuous variation of +10
dB about the center fre-
quency of each band.
When a control is raised, the
corresponding
frequency
range
is boosted,
and
when the control is lowered it Is attenuated.
When the controls are in the "O" (click) position, a
roughly flat response Is cbtained.
€ TAPE MONITOR switch
CONF sesh Seceastady set
to OFF
when
not
playing
back
(monitoring)
from
the tape deck
con-
nected.
6). ore
set to ON when playing back (monitor-
ing} from the tape deck connected.
'TAPE MONITOR
When
using a 3 head tape deck (erase, record and
playback heads all independent), the sound to be re-
corded can
be compared
instantaneously
with the
sound which has been recorded.
This check on the
quality of the recorded
sound is known
as the tape
monitor (for operating procedure, see pages 2 — 3).
OPERATION
Q@EQUALIZER selector switches
EPEAT acists eosd A flat frequency
response
is ob-
tained regardiess of the position of
the equalizer controls.
In this pesi-
tion, the green
indicator
above
the
switch lights up.
OTS catenteerecsae
set
to
tnis
position
for
adjust ting
sound
quality
with
the
graphic
equalizer. The green indicator above
the switch lights up. The quality of
the
sound
being
recorded
is ho-
wever not adjusted.
In this position, the sound adjusted
with the graphic equalizer can be re-
corded, and the red indicator above
the switch lights up. When the tape
monitor switch on the graphic equa-
lizer is set to OFF, the sound
to be
recorded can be heard. When using
the tape monitor, set to ON.
RECORDING...
NOTE:
® Do not depress 2 or more switches simultaneously.
® If none
of the 3 switches
are depressed,
the RE-
CORDING
indicator lignts up but no sound is heard
(not set to any position).
Make sure to press the
switches desired.
[1] WHEN
LISTENING
TO RECORDS
OR AM/FM
BROADCASTS,
ETC., THROUGH
THE GRAPHIC EQUALIZER
1. Set the input selector of the steréo
amplifier to
the source desired.
2. Set the tape monitor switch on the
fier to ON (TAPE).
3. Set the tone control on the stereo amplifier to give
a "flat" response (in the case of a tone switch, set
to DEFEAT).
stereo ampli-
4. Set the equalizer selector switches on the graphic
equalizer to ON.
5. Set the tape monitor switch on the graphic equa:
lizer to OFF.
6. Adjust the sound quality by means of the equalizer
controls.
2
pn or
Werbung
