HIKMICRO B-Serie Schnellstartanleitung Seite 6

Safety Instruction
These instructions are intended to ensure that user
can use the product correctly to avoid danger or
property loss.
Laws and Regulations
● Use of the product must be in strict compliance
with the local electrical safety regulations.
Transportation
● Keep the device in original or similar packaging
while transporting it.
● Keep all wrappers after unpacking them for future
use. In case of any failure occurred, you need to
return the device to the factory with the original
wrapper. Transportation without the original
wrapper may result in damage on the device and
the company shall not take any responsibilities.
● Do not drop the product or subject it to physical
shock. Keep the device away from magnetic
interference.
Power Supply
● The input voltage should meet the Limited Power
Source (3.7 VDC, 0.5 A) according to the IEC61010-1
standard. Please refer to technical specifications for
detailed information.
● Make sure the plug is properly connected to the
power socket.
● DO NOT connect multiple devices to one power
adapter, to avoid over-heating or fire hazards
caused by overload.
● Use the power adapter provided by a qualified
manufacturer. Refer to the product specification
for detailed power requirements.
Battery
● The built-in battery cannot be dismantled. Please
contact the manufacture for repair if necessary.
The battery may explode if it is replaced by an
incorrect type. Replace with the same or equivalent
type only. Dispose of used batteries in
conformance with the instructions provided by the
battery manufacturer.
● Use the battery provided by a qualified
manufacturer. Refer to the product specification
for detailed battery requirements.
● For long-term storage of the battery, make sure it is
fully charged every half year to ensure the battery
quality. Otherwise, damage may occur.
● Make sure the plug is properly connected to the
power socket.
● When the device is powered off and the RTC
battery is full, the time settings can be kept for
4 months.
● Before the first use, charge the lithium battery for
more than 8 hours.
Maintenance
● If the product does not work properly, please
contact your dealer or the nearest service center.
We shall not assume any responsibility for
problems caused by unauthorized repair or
maintenance.
● Wipe the device gently with a clean cloth and a
small quantity of ethanol, if necessary.
● If the equipment is used in a manner not specified
by the manufacturer, the protection provided by
the device may be impaired.
● Your camera will periodically perform a
self-calibration to optimize image quality and
measurement accuracy. In this process the image
will pause briefly and you will hear a "click" as a
shutter moves in front of the detector. The
self-calibration will be more frequent during the
startup or in very cold or hot environments. This is
a normal part of operation to ensure optimum
performance for your camera.
Calibration Service
● We recommend you send the device back for
calibration once a year, and please contact the local
dealer for the information on maintenance points.
For more detailed calibration services, please visit
https://www.hikmicrotech.com/en/support/calibra
tion-service.html.
Using Environment
● Make sure the running environment meets the
requirement of the device. The operating
temperature shall be -20 °C to 40 °C (-4 °F to
104 °F), humidity shall be 95% or less.
● Place the device in a dry and well-ventilated
environment.
● DO NOT expose the device to high electromagnetic
radiation or dusty environments.
● DO NOT aim the lens at the sun or any other bright
light.
● When any laser equipment is in use, make sure that
the device lens is not exposed to the laser beam, or
it may burn out.
Technical support
https://www.hikmicrotech.com/en/contact-us.html
will help you as a HIKMICRO customer to get the most
out of your HIKMICRO products. The portal gives you
access to our support team, software and
documentation, service contacts, etc.
Emergency
If smoke, odor, or noise arises from the device,
immediately turn off the power, unplug the power
cable, and contact the service center.
Manufacture Address
Room 313, Unit B, Building 2, 399 Danfeng Road,
Xixing Subdistrict, Binjiang District, Hangzhou,
Zhejiang 310052, China
Hangzhou Microimage Software Co., Ltd.
COMPLIANCE NOTICE: The thermal series products
might be subject to export controls in various
countries or regions, including without limitation, the
United States, European Union, United Kingdom
and/or other member countries of the Wassenaar
Arrangement. Please consult your professional legal
or compliance expert or local government authorities
for any necessary export license requirements if you
4