Kinderkraft CRUISER Bedienungsanleitung Seite 14

Do not let the child play with this product
Always use the restraint system
Check that the pram body or seat unit or car seat attachment
devices are correctly engaged before use
This product is not suitable for running or skating

Age and weight usage: from 0 months up to 15 kg.

We recommend using lowest reclined position for newborn babies.

This product may only be used by one child at the same time

The parking device shall be engaged when placing and removing the children

The maximum basket load is 2 kg.

Maximum weight of a bag attached to the adjustable handle is 1 kg.

Any additional load suspended from the buggy handles, backrest and sides will cause stability loss.

Use only parts and accessories supplied or recommended by the manufacturer. Do not use other parts or accessories.

Lift the front suspension when going up a curb or step.

Do not place the product near open flame or other heat sources.

Do not use with an additional platform.
B. ASSEMBLY
I. BUGGY COMPONENTS (FIG. 1)
A. Frame with seat and safety straps
B. Front wheels
C. Rear wheels
D. Tray / safety bar
E. Rear axle with brake / Set of wheel
fasteners
1. Pin x2
2. Cap x2
3. Plug x2
II. UNFOLDING BUGGY FRAME Place the frame on a flat surface with its handle up (FIG. 2). In order to unfold the frame,
move the lock (A) on the right side of the buggy and lift the frame up, until you hear the locking sound.
A properly unfolded frame is shown in FIG. 3.
III. WHEEL ASSEMBLY/DISASSEMBLY Put the rear wheel on the protruding part of the rear axle (FIG. 4). Press the plastic pin
(E1) on the axle, secure with the plastic cap (E2) and finish by covering with the plug (E3). Each of the elements should be
pressed with a slight resistance, until it locks into place. Repeat these steps on the other side of the buggy. To mount the
rear axle with the brake, put the rear free tips of the frame in the slots in the rear axle until you hear the lock click (FIG. 5).
Make sure to properly protect them with snap fasteners.
Insert the front wheels in the front axles until you hear the locking sound (FIG. 6). To remove the front wheels, push the
quick release button located below the footrest under each wheel (FIG. A). The buggy has a system of swivel front wheels
which can be locked in the straight-ahead position. To lock the wheel to move forward, slide the ring located above the
wheel (FIG. B).
NOTE! Before using the buggy, make sure that all the wheels are
properly installed.
IV. ASSEMBLY / DISASSEMBLY OF THE TRAY / SAFETY BAR AND LEG COVER The tray / safety bar must be inserted in
appropriate slots on both sides of the frame, as shown in Figure 7. To remove the part, press the release buttons on both
sides and remove the tray / safety bar (FIG. 8).
Leg cover has two Velcro fasteners located on the inner side. In order to attach the cover, slide the cover to be under the
tray and fasten the Velcro fasteners on the tubes of the seat frame just above the safety bar.
V. USE OF BRAKE The buggy is equipped with a foot brake located on the rear axle. Press the lower part of the brake
down; the brake is activated when you hear the locking sound (FIG. 9). Unlocking occurs after lifting the lower part of
brake lever.
VI. BACK AND FOOTREST ADJUSTMENT AND CUP HOLDER ASSEMBLY (FIG. 10) The footrest has 4 positions. Hold down
the buttons on both sides (FIG. A), to change the position of the footrest.
The seat is equipped with smooth backrest adjustment system, from a lying to a sitting position, using a clasp (FIG. B).
Cup holder is mounted on the left side of the buggy on the stem fixed to the frame (FIG. 11).
F. Cup holder
G. Leg cover
H. Rain cover
14