Makita HS6100 Bedienungsanleitung Seite 4

ENGLISH (Original instructions)
1-1. Lever
2-1. Front lever
3-1. Rear wing nut
4-1. Stopper
5-1. 0 ﾟ position
5-2. 45 ﾟ position
5-3. Cutting line
5-4. Screw
6-1. Switch trigger
6-2. Lock-off button
7-1. Light
8-1. Hex wrench
8-2. Loosen
8-3. Tighten
8-4. Shaft lock
9-1. Mounting shaft
SPECIFICATIONS
Model
Blade diameter
Max. cutting depth
No load speed (min
Overall length
Net weight
Safety class
• Due to our continuing programme of research and development, the specifications herein are subject to change without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for performing lengthways and
crossways straight cuts and mitre cuts with angles in
wood while in firm contact with the workpiece. With
appropriate saw blades, aluminum can also be sawed.
For public low-voltage distribution systems of
between 220 V and 250 V.
Switching operations of electric apparatus cause voltage
fluctuations. The operation of this device under
unfavorable mains conditions can have adverse effects
to the operation of other equipment. With a mains
impedance equal or less than 0.32 Ohms it can be
presumed that there will be no negative effects. The
mains socket used for this device must be protected with
a fuse or protective circuit breaker having slow tripping
characteristics.
Noise
The typical A-weighted noise level determined according
to EN60745:
All manuals and user guides at all-guides.com
Explanation of general view
9-2. Inner flange
9-3. Saw blade
9-4. Outer flange
9-5. Hex bolt
10-1. Mounting shaft
10-2. Inner flange
10-3. Saw blade
10-4. Outer flange
10-5. Hex bolt
11-1. Ring
11-2. Inner flange
11-3. Saw blade
11-4. Outer flange
11-5. Hex bolt
12-1. Hex wrench
13-1. Dust nozzle
at 0°
at 45°
at 50°
-1
)
ENE078-1
ENF100-1
Vibration
The vibration total value (tri-axial vector sum) determined
according to EN60745:
ENG905-1
4
13-2. Screw
14-1. Vacuum cleaner
14-2. Hose
16-1. Clamp lever
16-2. Rip fence (Guide rule)
17-1. Adjusting screw for 0 ﾟ
17-2. Adjusting screw for 45 ﾟ
18-1. Triangular rule
19-1. Base
19-2. Screw
19-3. Saw blade
20-1. Limit mark
21-1. Screwdriver
21-2. Brush holder cap
HS6100 HS6101
165 mm
54.5 mm
39.5 mm
35.5 mm
5,500
297 mm
3.7 kg 3.7 kg
/II
Model HS6100,HS6101
Sound pressure level (L
Sound power level (L
WA
Uncertainty (K) : 3 dB(A)
Model HS7100,HS7101
Sound pressure level (L
Sound power level (L
WA
Uncertainty (K) : 3 dB(A)
Wear ear protection
Model HS6100,HS6101
Work mode : cutting wood
Vibration emission (a
h,W
Uncertainty (K) : 1.5 m/s
HS7100 HS7101
190 mm
67 mm
48.5 mm
43.5 mm
310 mm
4.0 kg 4.0 kg
) : 89 dB(A)
pA
) : 100 dB(A)
) : 90 dB(A)
pA
) : 101 dB(A)
ENG900-1
2
) : 2.5 m/s or less
2