Werbung
Verfügbare Sprachen
Verfügbare Sprachen
7. DECOMMISSION AND DISMANTLEMENT
Follow the instructions for removing the unit from service during
dismantlement. Destruction of the unit must be carried out in compliance
with local regulations on waste disposal.
This product falls within the scope of Directive 2012/19/EU
regarding the management of electrical and electronic
equipment waste (WEEE).
Electronic-electrical equipment must not be disposed of with
domestic waste as it is made of various materials that can be
recycled at the appropriate facilities. Inquiries should be made
through the municipal authorities regarding the location of the ecological
platforms that receive products for disposal and their subsequent correct
recycling.
This product is not potentially dangerous for human health and the
environment, since it does not contain harmful substances as per
Directive 2011/65/EU (RoHS), yet if abandoned in the environment it has
a negative impact on the ecosystem.
Read the instructions carefully before using the appliance for the first
time. It is recommended that you do not use this product for any purpose
other than that for which it was intended; there is danger of electric shock
if used improperly.
The crossed-out bin symbol found on the appliance label indicates the
compliance of this product with the regulations regarding electrical and
electronic equipment waste.
Abandoning the appliance in the environment or its illegal disposal is
punishable by law.
8. TROUBLESHOOTING
SYMPTOM
PROBABLE CAUSE
1.
Ossi-mix
1.1 The selection switch
is positioned on "Off".
does not start
1.2 There is no power
supply.
1.3
The
automatic
control
mechanisms
(level regulator, thermal
amperometer,
refuse consent.
2.
The
2.1 Full voltage is not
overload
reaching all phases of
breaker or the
the motor.
thermal
2.2
Absorption
amperometer
unbalanced
over
protection
phases.
triggers
2.3 The motor is running
during
inverted.
operation.
2.4 the overload circuit
breaker has a too low
setting.
2.5 the power supply
voltage
does
correspond to the ossi-
mix's voltage.
2.6 The rotor is not
rotating freely because
of attrition.
2.7 The liquid being
aerated/mixed
excessively
dense
viscous.
2.8
The
electrical
control
panel
overheated.
2.9 The electrical motor
has overheated.
2.10 The motor winding
mechanism
has
damaged
by
presence of liquids.
RECOMMENDED ACTION
1.1 Switch to "on".
1.2 Check that the electrical
equipment is undamaged and
that the power supply is on.
1.3 Wait for consent and
check the efficiency of the
control mechanisms.
etc.)
2.1 Check that the electrical
equipment is undamaged and
the power supply voltage.
is
2.2 Check the phase balance
the
as detailed in the wiring and
grounding
section.
necessary send the ossi-mix
to an authorized repair shop.
2.3 Invert two of the three
phases.
2.4
Check
the
ampere
calibration corresponds to the
not
specification on the ossi-mix
nameplate.
2.5 Substitute the ossi-mix or
the change the power supply.
2.6 Check the hydraulics as
detailed in the "maintenance"
section. If necessary send the
is
ossi-mix to an authorized
or
repair shop.
2.7
Revise
the
ossi-mix
selection.
has
2.8 Check that the circuit
breakers are at compensated
ambient temperature. Protect
the electrical control panel
from direct sunlight and heat
been
sources.
the
2.9 Remove scaling from the
motor
cooling
surfaces.
Reconsider
the
ossi-mix
model choice on the basis of:
- the temperature of the
treated liquid;
- the shallow level of the
liquid does not cover the
motor.
2.10 Check as instructed in
the maintenance section. If
necessary send the ossi-mix
3. The ossi-
3.1
mix does not
control
stop
(level regulator, thermal
automatically.
amperometer,
refuse consent.
4. Air flow is
4.1 Rotation direction is
weak.
inverted.
4.2 Ossi-mix is worn
out.
4.3 Ossi-mix is partially
obstructed.
5. The ossi-
5.1 The unit has been
mix is noisy
installed wrong.
and vibrates.
5.2 Worn hydraulics.
5.3
contains an excessive
percentage of solids.
If
9
en
« Translation of the original instructions »
to an authorized repair shop.
The
automatic
3.1 See 1.3.
mechanisms
etc.)
4.1 Invert two of the three
phases.
4.2 Check the hydraulics as
detailed in the "maintenance"
section.
4.3 Eliminate detritus.
5.1 See 4.1.
5.2 See 4.2.
5.3 Reconsider the ossi-mix
Treated
liquid
model choice.
Werbung
