Gude Expert Power Control 8221 Serie Expert Power Control 8226 Serie Anleitung Seite 81

Spezifikationen
port {port_num} twinport show
port {port_num} initstate coldstart set {OFF=0|
ON=1|REMEMBER=2}
port {port_num} initstate coldstart show
port {port_num} initstate repower set
{INIT_STATE=0|CURRENT_STATE=1}
port {port_num} initstate repower show
port {port_num} initstate delay set {num}
port {port_num} initstate delay show
port {port_num} repowerdelay set {num}
port {port_num} repowerdelay show
port {port_num} resettime set {num}
port {port_num} resettime show
port {port_num} watchdog enabled set {OFF=0|
ON=1}
port {port_num} watchdog enabled show
port {port_num} watchdog mode set {OFF=0|
PORT_RESET=1|IP_MS=2|IP_MS_INV=3}
port {port_num} watchdog mode show
port {port_num} watchdog type set {WD_ICMP=0|
WD_TCP=1}
port {port_num} watchdog type show
port {port_num} watchdog link down set {OFF=0|
ON=1}
port {port_num} watchdog link down show
port {port_num} watchdog host set "{dns_name}" sets port watchdog host target
port {port_num} watchdog host show
port {port_num} watchdog port set {ip_port}
port {port_num} watchdog port show
port {port_num} watchdog pinginterval set {num}
port {port_num} watchdog pinginterval show
port {port_num} watchdog pingretries set {num}
port {port_num} watchdog pingretries show
port {port_num} watchdog retrybooting set
{OFF=0|ON=1}
port {port_num} watchdog retrybooting show
port {port_num} watchdog bootretries set {num}
port {port_num} watchdog bootretries show
port ignore powerloss {BANK_A=1|BANK_B=2}
set <off=0/on=1>
port ignore powerloss {BANK_A=1|BANK_B=2}
show
portsensor
portsensor all {field_list} show
portsensor {port_num} {field_list} show
portsensor {port_num} {energy_sensor} value
show
portsensor {port_num} counter reset
portsensor {port_num} {energy_sensor} events set
{OFF=0|ON=1}
portsensor {port_num} {energy_sensor} events
show
portsensor {port_num} {energy_sensor} events ty-
pe set
"{EVT_SYSLOG=0,EVT_SNMP=1,EVT_EMAIL=2
,EVT_SMS=3,EVT_GSMEMAIL=4,EVT_BEEPER
=5,EVT_DISPLAY=6,EVT_CONSOLE=7}"
portsensor {port_num} {energy_sensor} events ty-
pe show
portsensor {port_num} {energy_sensor} events
beeper mode set {CONTINOUS=0|
INTERMITTENT=1}
portsensor {port_num} {energy_sensor} events
beeper mode show
portsensor {port_num} {energy_sensor} maxval
set {num}
portsensor {port_num} {energy_sensor} maxval
show
portsensor {port_num} {energy_sensor} minval set
{num}
portsensor {port_num} {energy_sensor} minval
show
portsensor {port_num} {energy_sensor} hyst set
{num}
81
Expert Power Control 8221/8226
shows port {num} twinport state
sets port coldstart initialization
shows port coldstart initialization
sets port initialization for bank repower
shows port initialization for bank repower
sets port init delay
shows port init delay
sets port repower delay
shows port repower delay
sets port reset duration
shows port reset duration
sets port watchdog to on/off
shows port watchdog state
sets port watchdog mode
shows port watchdog mode
sets port watchdog type
shows port watchdog type
sets if watchdog active when eth link down
shows if watchdog active when eth link down
shows port watchdog host target
sets port watchdog TCP port
shows port watchdog TCP port
sets port watchdog ping interval
shows port watchdog ping interval
sets port watchdog ping retries
shows port watchdog ping retries
sets port watchdog retry booting to on/off
shows port watchdog retry booting state
sets port watchdog retry boot timeout
hows port watchdog retry boot timeout
enable no powerport shutdown when powerloss
detected
show if powerloss is ignored
enters cmd group "portsensor"
shows energy sensors according field list of all
port sensors
shows energy sensors according field list of one
port sensor
shows energy sensor of given port
resets energy metering counter
enables sensor events on/off
shows if sensor events are enabled
enables different event types
shows what event types are enabled
sets beeper tone
shows beeper tone
sets maximum value for sensor
shows maximum value for sensor
sets minimum value for sensor
shows minimum value for sensor
sets hysterese value for sensor
5
5
5
© 2021 GUDE Systems GmbH