Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
NETWORK SETUP
-------------------------------------------------------------------------------------------
Technical requirements
Most of the home networks are Dynamic. If you
have a dynamic network, you must use a DSL
modem that supports DHCP. Modems and IP
sharers that support DHCP obtain the »IP Ad-
dress«, »Netmask«, »Gateway« and »DNS«
values required for internet access automatically,
and thus you are not required to enter those val-
ues manually.
Wireless WPS network connection
through by pressing a button
1
Open the menu with »MENU«.
2
Activate the menu item »Settings« with
»OK«.
3
Select the menu item »Network Configura-
>
<
tion« with »
« or »
« and press »OK« to
confirm.
– »Network configuration« menu is dis-
played.
4
Select the line »Change Connection Type«
with »
« or »
« and press »OK« to con-
V
Λ
firm.
5
Select the option »Wireless WPS« with »
<
«
or »
>
« and press »OK« to confirm.
– WiFi warning screen will be displayed.
6
Activate WiFi with » « (green).
7
Select the line »WPS Type« with »
« or
V
»
« and select the option »Push Button«
Λ
with »
<
« or »
>
«.
Timer Applications
TV Settings
Network Configuration
Change Connection Type
Wireless WPS
WiFi
On
WPS Type
Push Button
Select Access Point
N/A
Network Configuration
AUTO
Advanced
Connect
Test Connection
Change Area
Back
Exit
8
With » « (red) select »Connect« to establish
modem connection.
– »Push the WPS button on your Access
Point« message is displayed.
9
Press the WPS button on the router.
36
ENGLISH
10
To continue after pressing the WPS button
on the access point, press » « (green).
– The "Connection to Gateway: Success"
message will be displayed.
11
Press » « (green) to make sure that the
network connection is established with the
current settings.
– »Testing ... Please wait« message will
be displayed, and if the connection is
established »Connection To Gateway:
Success«, »Internet Connection: Success«
messages will be displayed.
12
Press »EXIT« to end the setting.
Wireless WPS network connection
with PIN
1
Open the menu with »MENU«.
2
Activate the menu item »Settings« with
»OK«.
3
Select the menu item »Network Configura-
tion« with »
>
« or »
<
« and press »OK« to
confirm.
– »Network configuration« menu is dis-
played.
4
Select the line »Change Connection Type«
with »
« or »
« and press »OK« to con-
V
Λ
firm.
5
<
Select the option »Wireless WPS« with »
«
>
or »
« and press »OK« to confirm.
– WiFi warning screen will be displayed.
6
Activate WiFi with » « (green).
7
Select the line »WPS Type« with »
« or
V
»
« and select the option »PIN« with »
<
«
Λ
>
or »
«.
Timer Applications
Network Configuration
TV Settings
Change Connection Type
Wireless WPS
WiFi
On
WPS Type
PIN
Select Access Point
N/A
Network Configuration
AUTO
Advanced
Change Area
Back
Exit
NETWORK SETUP
-------------------------------------------------------------------------------------------
8
Select the line »Select Access Point« with
»
« or »
« and press »OK« to confirm.
V
Λ
– Present WPS-supported wireless networks
are scanned to display in the »Select Ac-
cess Point« menu.
9
Select the network that you want to connect
<
>
with »
«, »
«, »
« or »
« and press »OK«
V
Λ
to confirm.
– 8-digit pin code is displayed in the wire-
less WPS menu.
Note:
Refer to the manual of your router to find out
7
how the PIN is entered via a PC.
10
Use a PC to enter the pin on the router (e.g.
AVM FRITZ!Box: menu item WLAN Set-
tings... WPS) and save.
Note:
The 8-digit PIN code must be entered in the
7
modem interface in 2 minutes; otherwise,
connection of television with the modem is
cut.
11
Press » « (green) to confirm the registra-
tion.
– The message "Connection to Gateway:
Success" appears.
12
Press » « (green) to check the performed
settings and also if the local network and
internet connection has been established.
– »Testing ... Please wait« message will
be displayed, and if the connection is
established »Connection To Gateway:
Successfull«, »Internet Connection: Suc-
cessfull« messages and MAC address will
be displayed.
13
Press »EXIT« to end the setting.
Connecting automatically by enter-
ing the network password
Use this method for establishing a connection
if your router does not support "WPS-PBC" or
WPS PIN entry.
1
Open the menu with »MENU«.
2
Activate the menu item »Settings« with
»OK«.
3
Select the menu item »Network Configura-
>
<
tion« with »
« or »
« and press »OK« to
confirm.
– »Network configuration« menu is dis-
played.
Timer Applications
TV Settings
Network Configuration
Change Connection Type
Wired
OK
Network Configuration
AUTO
Advanced
Connect
Test Connection
Change Area
Back
Exit
4
Select the line »Change Connection Type«
with »
« or »
« and press »OK« to con-
V
Λ
firm.
5
Select the option »Wireless« with »
<
« or
>
»
« and press »OK« to confirm.
– WiFi warning screen will be displayed.
6
Activate WiFi with » « (green).
7
Select the line »Network Configuration«
with »
« or »
« and select the option
V
Λ
<
>
»AUTO« with »
« or »
«.
8
Select the line »Select Access Point« with
»
« or »
« and press »OK« to confirm.
V
Λ
– »Select Access Point« menu is displayed
by scanning available wireless networks.
9
Select the network that you want to connect
<
>
with »
«, »
«, »
« or »
« and press »OK«
V
Λ
to confirm.
– Wireless connection password screen is
displayed.
Note:
For device to discover the wireless modem
7
on the network, the network name should
support ASCII characters.
ENGLISH
37
Quicklinks ausblenden:
Werbung
Inhaltsverzeichnis
