Grundig 40 VLE 5430 BP Servicehandbuch Seite 66

SETTINGS
------------------------------------------------------------------------------------------------------------------
Tuning cable digital television chan-
nels (DVB-C)
26 < >
Select the option »Cable« with » « or » «
and press »OK« to confirm.
27
Select the line »Scan Type« with » « or
V
» «.
Λ
Select the option »Quick« or »Full« with » < «
>
or » «.
– »Quick« scanning function sets the chan-
nels according to the cable operator
information in the broadcasting signal.
– »Full« scan function scans the entire fre-
quency range selected. With this search
option, search can take a long time. This
search type is recommended. Some cable
providers do not support »Quick« scan.
Note:
You can speed up the search. To do this,
7
frequency and network ID information are
required. You may get this data from your
cable operator or find it in the Internet fo-
rums.
28
Use » « to select the push button »Next
V
Page« and confirm with »OK«.
Note:
<
Perform Channel Type selection. Press » «
7
or » > « to select whether you want to search
for only digital channels (Digital), only Ana-
log channels (Analog) or both (Digital +
Analog) and press »OK« to select and mark
or unmark the »Digital« and »Analog« items.
29 Press » « (red) to start searching.
– The »Automatic Channel Search« menu
appears, and the search for TV channels
begins.
– The scan is complete as soon as the
»Search is completed!« appears.
30 Select the »Channel Editor« with » « (red).
18 ENGLISH
Tuning terrestrial digital television
channels (DVB-T)
31 < >
Select the option »Air« with » « or » « and
press »OK« to confirm.
Important:
The antenna power supply (5V ) may only
7
be switched on if the antenna is an active
indoor antenna with a signal amplifier and
it is not already supplied with a voltage via
a mains plug (or similar supply). Otherwise
you may cause a short circuit and irrepara-
bly damage your antenna.
32
Select the line »Active Antenna Power« with
» « or » «.
V Λ
Switch on the antenna power supply for the
antenna with » < « or » > « (»On«).
33 Select the line »Next Page« with » « or
V
» « and press »OK« to confirm.
Λ
Note:
<
Perform Channel Type selection. Press » «
7
or » > « to select whether you want to search
for only digital channels (Digital), only Ana-
log channels (Analog) or both (Digital +
Analog) and press »OK« to select and mark
or unmark the »Digital« and »Analog« items.
34 Press » « (red) to start searching.
– The »Automatic Channel Search« menu
appears, and the search for TV channels
begins.
– The scan is complete as soon as the
»Search is completed!« appears.
35 Select the »Channel Editor« with » « (red).
SETTINGS
------------------------------------------------------------------------------------------------------------------
Changing the Channel Editor for
the digital channels
Channels found at the end of the search are
stored in the »Channel Editor«.
You can delete channels which are not required
from the programe table, you can change the
order of channels within the programe table and
lock individual channels (Parental control).
You can also add channels to the favourites list;
in addition, you can change the order of chan-
nels within the favourites list.
In Channel Editor, press »P+« to switch the chan-
nel list to the next page, press »P–« to switch it
back to the previous page.
To perform searching in the Channel Editor menu
by Channel names, press » « (red).
To display the channels in the Channel Editor
menu by Antenna Type, press » « (green) and
»OK«.
To use filters and tools in the Channel Editor
menu, press » « (yellow).
11 HD1
1080i
Channel Editor
Das Erste ZDF SAT1
1 2
24 HD Sport HD Test
6 7
HD1 Life Film
11 12
TV Sport SAT8 SKY
16 17
Search
Opening the Programme Table
1 Open the menu with »MENU«.
2 Activate the »Settings« menu with »OK«.
3 >
Select the option »Source Setup« with » «
or » < « and press »OK« to confirm.
4 Select the line »Channel Editor« with » « or
V
» « and press »OK« to confirm.
Λ
– »Channel Editor« menu is displayed.
Important:
Programme table and favourite lists are
7
stored separately for all sources (satellite,
cable and air).
Programme table of the current source will
7
be displayed when you select programme
table.
Notes:
A Cl module and smart card is required to
7
watch the channel if there is a » « sign next
to the channel name in Programme Table.
As the recorded data channels are not dis-
7
played in the channel list, number of chan-
nels displayed in the Channel list may be
less than 6000
dd.mm.yyyy hh:mm
Satellite All
N24 SAT3
3 4 5
3 SAT RTL
8 9 10
Promo Sport1
13 14 15
TV6 TV5
18 19 20
Antenna Type Tools Tune Channel
for Channels
ENGLISH 19