Makita HR3011FCJ Betriebsanleitung Seite 10

WARNING:
Wear ear protection.
WARNING:
The noise emission during actual
use of the power tool can differ from the declared val-
ue(s) depending on the ways in which the tool is used
especially what kind of workpiece is processed.
WARNING:
Be sure to identify safety measures
to protect the operator that are based on an estima-
tion of exposure in the actual conditions of use (tak-
ing account of all parts of the operating cycle such
as the times when the tool is switched off and when
it is running idle in addition to the trigger time).
Vibration
The following table shows the vibration total value
(tri-axial vector sum) determined according to applica-
ble standard.
Model HR3011FC
Work mode Vibration
emission
2
Hammer 9.5 m/s
drilling into
concrete
(a )
h, HD
2
Hammer 9.5 m/s
drilling into
concrete with
DX10 (a )
h, HD
2
Chiselling func- 6.0 m/s
tion with side
grip (a )
h, Cheq
2
Drilling into 5.5 m/s
metal (a )
h, D
Model HR3012FC
Work mode Vibration
emission
2
Hammer 9.5 m/s
drilling into
concrete
(a )
h, HD
2
Hammer 8.0 m/s
drilling into
concrete with
DX11 (a )
h, HD
2
Chiselling func- 5.5 m/s
tion with side
grip (a )
h, Cheq
2
Drilling into 6.0 m/s
metal (a )
h, D
Model HR3001C
Work mode Vibration
emission
2
Hammer 13.5 m/s
drilling into
concrete
(a )
h, HD
2
Chiselling func- 11.0 m/s
tion with side
grip (a )
h, Cheq
2
Drilling into 6.0 m/s
metal (a )
h, D
Uncertainty (K) Applicable
standard
2
1.5 m/s EN60745-2-6
2
1.5 m/s EN60745-2-6
2
1.5 m/s EN60745-2-6
2
1.5 m/s EN62841-2-1
Uncertainty (K) Applicable
standard
2
1.5 m/s EN60745-2-6
2
1.5 m/s EN60745-2-6
2
1.5 m/s EN60745-2-6
2
1.5 m/s EN62841-2-1
Uncertainty (K) Applicable
standard
2
1.5 m/s EN60745-2-6
2
1.5 m/s EN60745-2-6
2
1.5 m/s EN62841-2-1
NOTE: The declared vibration total value(s) has been
measured in accordance with a standard test method
and may be used for comparing one tool with another.
NOTE: The declared vibration total value(s) may also
be used in a preliminary assessment of exposure.
WARNING:
use of the power tool can differ from the declared val-
ue(s) depending on the ways in which the tool is used
especially what kind of workpiece is processed.
WARNING:
to protect the operator that are based on an estima-
tion of exposure in the actual conditions of use (tak-
ing account of all parts of the operating cycle such
as the times when the tool is switched off and when
it is running idle in addition to the trigger time).
EC Declaration of Conformity
For European countries only
The EC declaration of conformity is included as Annex A
to this instruction manual.
SAFETY WARNINGS
General power tool safety warnings
WARNING:
tions, illustrations and specifications provided with this
power tool. Failure to follow all instructions listed below
may result in electric shock, fire and/or serious injury.
Save all warnings and instruc-
tions for future reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
ROTARY HAMMER SAFETY WARNINGS
1. Wear ear protectors. Exposure to noise can
cause hearing loss.
2. Use auxiliary handle(s), if supplied with the
tool. Loss of control can cause personal injury.
Hold power tool by insulated gripping surfaces,
3.
when performing an operation where the cutting
accessory may contact hidden wiring or its own
cord. Cutting accessory contacting a "live" wire
may make exposed metal parts of the power tool
"live" and could give the operator an electric shock.
4. Wear a hard hat (safety helmet), safety glasses and/
or face shield. Ordinary eye or sun glasses are NOT
safety glasses. It is also highly recommended that
you wear a dust mask and thickly padded gloves.
5. Be sure the bit is secured in place before operation.
6. Under normal operation, the tool is designed
to produce vibration. The screws can come
loose easily, causing a breakdown or accident.
Check tightness of screws carefully before
operation.
10 ENGLISH
The vibration emission during actual
Be sure to identify safety measures
Read all safety warnings, instruc-