Grohe EUROSMART COSMOPOLITAN E 36 327 Montageanleitung Seite 8

2. Remove finger from the sensor system while
displayed.
Cleaning mode is terminated.
Signalling the remaining battery capacity and performing
continuous operation for thermal disinfection
1. Turn mixer lever to the hot water end stop.
2. Hold finger against the lower area of the sensor system,
see Fig. [9].
Indicator lamp signals:
█████████████████████ ██ ██ ██ ██ ██ ██ ██ ▌▌▌▌▌
3. Remove finger from the sensor system while
is displayed.
The remaining battery capacity is signalled by the number
of flashing signals:
Remaining battery capacity > 60%
██ ██ ██ ██
Remaining battery capacity > 40%
██ ██ ██
Remaining battery capacity > 20%
██ ██
Remaining battery capacity < 20%
██
The remaining battery capacity is always indicated
by 4 flashing signals during mains operation.
Take hands out of the detection zone of the sensor
system.
Thermal disinfection starts once the remaining capacity has
been signalled.
If an object is detected during thermal disinfection, the water
stops flowing immediately and the fitting is closed (indicator
lamp starts to flash).
Closure of the fitting ends automatically after 3 minutes or can
be prematurely terminated (see Terminating cleaning mode).
Making settings
Setting mode
Setting mode has the following functions:
- Querying and changing the programme
- Checking the detection zone
The indicator lamp in the sensor system illuminates in setting
mode when the detection zone of the fitting is reached by an
approaching user.
Activating setting mode
Disconnect the power supply to the electronics and reconnect
after 10 s, see fold-out page I, Fig. [10].
• Setting mode is automatically terminated after 3 minutes.
Setting the programme
1. Activate setting mode.
2. Hold finger against the lower area of the sensor system,
see Fig. [9].
Indicator lamp signals:
▌▌▌▌▌▌▌▌▌▌▌▌▌▌▌▌▌▌___
3. Remove finger from the sensor system while
displayed.
Programme selection mode is active for 60 s.
5
is 4. Hold finger against the lower area of the sensor system.
____
The programmes are displayed by groups of flashing
signals via the indicator lamp. Display starts with
the programme that is currently set.
██
██ ██
██ ██ ██
██ ██ ██ ██
██ ██ ██ ██ ██
██ ██ ██ ██ ██ ██
██ ██ ██ ██ ██ ██ ██
5. Remove finger from the sensor system after the desired
sequence of flashing signals.
▌▌▌▌
The programme is adopted as the new setting. The
corresponding flashing signals are displayed again.
The setting can be readjusted within the next 6 s if necessary
Setting mode is automatically terminated after 3 minutes.
Maintenance
• Shut off hot and cold water supply.
• Disconnect voltage supply.
• Inspect and clean all components and replace if necessary.
I. Battery, see fold-out page I, Fig. [11].
Batteries which are almost discharged are displayed by
a flashing indicator lamp in the sensor system.
Assemble in reverse order.
II. Solenoid valve, see fold-out page I, Figs. [7] and fold-out
page II, Figs. [12] to [14].
Assemble in reverse order.
Observe correct installation position of individual
components, see details, Fig [15].
III. Remove and clean mousseur (42 832), see fold-out page II
Assemble in reverse order.
IV. Mixer spindle, see fold-out pages I and II.
1. Disconnect fitting from connections.
2. Remove fitting from wash basin.
Disassembly is as described in section "Setting temperature
limiter", see Fig. [7].
3. Pull out mixer spindle and replace, see Fig. [16].
Assemble in reverse order.
Replacement parts
see fold-out page II (* = special accessories)
Care
For directions on the care of this fitting, please refer to the
accompanying Care Instructions.
Disposal note
is
____
Dispose of batteries in accordance with national
regulations.
Programme 1
Programme 2
Programme 3
Programme 4
Programme 5
Programme 6
Programme 7
(see 4.)