EINHELL TE-BF 18 Li Originalbetriebsanleitung Seite 19

5. Before starting the equipment
Warning!
Always remove the battery pack before making
adjustments to the equipment.
5.1 Installing the dust extractor adapter
(Figure 2-3/ Item 8)
The connection for the dust extraction adapter (6)
is closed by the sealing plug (7). To remove the
plug simply pull it out of the opening.
You can then plug the dust extraction adapter (8)
into the connection for the dust extraction adapter
(6).
You can then connect a suitable dust extractor (a)
to the dust extractor adapter (8) (dust extractor
not supplied).
This will provide excellent dust extraction on the
workpiece.
Check that all the parts are properly connected.
Important. The vacuum cleaner you use for the
extraction work must be suitable for the workpie-
ce material.
5.2 Changing the grinding/sanding belt
(Fig. 4-8/Item 12)
•
Press the clamping lever for the grinding/san-
ding belt (9) forwards until you hear it latch in
place.
•
Now you can place the grinding/sanding belt
(12) around the drive roller as shown in Fig. 6
(11) and then around the tip of the grinding/
sanding belt arm (13) (Fig. 7).
•
Make sure that the running direction of the
grinding/sanding belt (see arrow on the inside
of the grinding/sanding belt) is the same as
the running direction of the cordless belt file.
•
Pull the clamping lever (9) back to the rear in
order to tension the grinding/sanding belt.
5.3 Adjusting the belt running position
(Fig. 9/Item 10)
•
Hold the cordless belt file by the handle and
switch it on with the On/Off switch (5).
•
By turning the setting screw for adjusting the
grinding/sanding belt (10) you must adjust the
belt running position such that the grinding/
sanding belt (12) runs centrally on the grin-
ding/sanding belt arm (13).
Anl_TE-BF_18_Li_SPK13.indb 19 Anl_TE-BF_18_Li_SPK13.indb 19
GB
5.4 Changing the grinding/sanding belt arm
(Fig. 10/Item 13)
•
The cordless belt file is supplied complete
with an 8mm grinding/sanding belt arm and a
13mm grinding/sanding belt arm.
•
To change the grinding/sanding belt arm (13)
remove the grinding/sanding belt (12) as de-
scribed in 5.2.
•
Then fully unscrew the adjustment screw for
adjusting the grinding/sanding belt (10).
•
Now you can easily remove the grinding/
sanding belt arm and fit the other grinding/
sanding belt arm in reverse order.
5.5 Adjusting the angle of the swiveling gear
head (Fig. 11/Item 16)
•
You can swivel the swiveling gear head (16)
by up to 90°.
•
To do so, press the clamping lever (15) for-
wards.
•
Now you can swivel the gear head into the
position required.
•
Then pull the clamping lever (15) back to
the rear in order to secure the swiveling gear
head (16) again.
•
Finally, check that the swiveling gear head
(16) is securely seated.
6. Starting up
6.1 Switching ON/OFF (Fig. 12)
To switch on:
Press the ON/OFF switch (5).
Continuous operation:
Secure the switch (5) with the locking button (4).
To switch off :
Press the ON/OFF switch (5) briefl y.
The machine can be operated on a temporary or
permanent setting.
6.2 Setting the belt speed (Fig. 12/ Item 3)
You can select the belt speed by turning the set-
ting knob (3).
PLUS direction:
Increase belt speed
MINUS direction:
Reduce belt speed
- 19 -
21.06.2023 14:35:07 21.06.2023 14:35:07