Makita PW5000C Betriebsanleitung Seite 7

WARNING:
Read and observe these precau-
tions before using the tool. Non-observance of
these precautions may lead to personal injuries
and damage to the tool!
The tool was built according to the European Standards
EN62841-1 (safety of hand-held, motor-driven power
tools; here in particular section of power tools with water
connection) and EN60309-2 (plugs, receptacles and
couplings for industrial applications). When applying
these standards, the earth contact position of the plug-in
device may only be carried out in "12 o'clock position".
The tool has a plug-in device with a "12 o'clock"
earth contact position.
However, since the European Standard EN60309-2 does
not provide a differentiation regarding the supply voltage
and this earth contact position, there is the possibility to
confuse the connection to an isolating transformer with
another output voltage (e.g. 230 V). When connecting the
tool to an isolating transformer, make absolutely sure to
use the correct output voltage (110 V, 50 - 60 Hz).
This tool is designed exclusively for connection to
an isolating transformer with an output voltage of
110 V. Due to its use in wet conditions (water connec-
tion on the tool), this tool must never be connected
to a power supply without an isolating transformer.
Damages caused by inappropriate tampering with the plug-in
device are not subject to warranty or legal guarantee claims.
Contact your specialist supplier for an isolating
transformer suitable for your tool.
FUNCTIONAL
DESCRIPTION
CAUTION:
Always be sure that the tool is
switched off and unplugged before adjusting or
checking function on the tool.
Shaft lock
WARNING:
Never actuate the shaft lock when
the spindle is moving. It may cause serious injury or
the tool damage.
Press the shaft lock to prevent spindle rotation when
installing or removing accessories.
► Fig.1: 1. Shaft lock
Switch action
CAUTION:
Before plugging in the tool, always
check to see that the slide switch actuates prop-
erly and returns to the "OFF" position when the
rear end of the slide switch is depressed.
CAUTION:
Switch can be locked in the "ON"
position for ease of operator comfort during
extended use. Apply caution when locking tool in
the "ON" position and maintain firm grasp on tool.
To start the tool, press down the rear end of the slide
switch and then slide it toward the "I (ON)" position.
For continuous operation, press down the front end of
the slide switch to lock it.
► Fig.2: 1. Slide switch
To stop the tool, press down the rear end of the slide
switch so that it returns to the "O (OFF)" position.
► Fig.3: 1. Slide switch
Speed adjusting dial
The rotation speed of the tool can be changed by turn-
ing the speed adjusting dial. The table below shows
the number on the dial and the corresponding rotation
speed.
► Fig.4: 1. Speed adjusting dial
Number
1
2
3
4
5
NOTICE:
If the tool is operated continuously at
low speed for a long time, the motor will get over-
loaded, resulting in tool malfunction.
NOTICE:
The speed adjusting dial can be turned
only as far as 5 and back to 1. Do not force it past
5 or 1, or the speed adjusting function may no
longer work.
Constant speed control
Possible to get fine finish, because the rotating speed is
kept constantly even under the loaded condition.
Soft start feature
Soft start feature reduces starting reaction.
Overload protector
When the load on the tool exceeds admissible levels,
power to the motor is reduced to protect the motor from
overheating. When the load returns to admissible lev-
els, the tool will operate as normal.
Opening or closing of water lever
To keep the lever on the tool for water flow open, turn it
to the position A where the water passage will be ready.
Return it to the position B to close.
► Fig.5: 1. Lever 2. Open 3. Close
7 ENGLISH
Speed
-1
2,000 min
-1
2,500 min
-1
3,000 min
-1
3,500 min
-1
4,400 min