Bestway STEEL PRO Bedienungsanleitung Seite 6

POWER STEEL™ FRAME POOL
Dimension: 14' x 48''
Description
Part N.
Complete structure
A Top Rail
B Vertical Pool Leg
C T-connector
D Pin
E Footing
F Pin Gasket
J Pool liner (Grey / Brown)
H Hose adaptor
Spring-loaded Pin
K
Dimension: 18' x 52''
Part N. Description
Complete structure
A Top Rail
B Vertical Pool Leg
C T-connector
D Pin
Footing
E
F Pin Gasket
J Pool liner
H Hose adaptor
K Spring-loaded Pin
Dimension: 16' x 48''
Part N. Description
Complete structure
A Top Rail
B Vertical Pool Leg
C T-connector
D Pin
E Footing
F Pin Gasket
J Pool liner
H Hose adaptor
Spring-loaded Pin
K
CHOOSE THE CORRECT LOCATION
NOTE: The pool must be set up on a completely flat and level surface. Please do not install the pool if
the surface is inclined or sloped.
Correct conditions to set up the pool:
• The selected location has to be capable of uniformly supporting the weight for the entire time the pool is
installed, moreover the location must be flat and must be cleared of all objects and debris including stones
and twigs.
• We recommend positioning the pool away from any objects children could use to climb into the pool.
NOTE: Position the pool near an adequate drainage system to deal with overflow or to discharge the pool.
Incorrect conditions to set up the pool:
• On uneven ground the pool may collapse causing serious personal injury and/or damage to personal
property and will void the warranty and prevent any service claims.
• Sand should not be used to create a level base; the ground must be dug out if necessary.
• Directly under overhead power lines or trees. Be sure the location does not contain underground utility
pipes, lines or cables of any kind.
• Do not set up the pool on driveways, decks, platforms, gravel or asphalt surfaces. The selected location
should be firm enough to withstand the pressure of the water; Mud, sand, soft / loose soil or tar are not
suitable.
• Grass or other vegetation under the pool will die and may cause odors and slime to develop, therefore we
recommend removing all grass from the selected pool location.
• Avoid areas prone to aggressive plant and weed species that may grow through the ground cloth or liner.
NOTE: Check with your local city council for by-laws relating to fencing, barriers, lighting and safety
requirements and ensure you comply with all laws.
NOTE: If have a filter pump, refer to the pump's manual for instructions.
NOTE: The ladder must match the pool size and should to be used only for entering and exiting the pool. It
is forbidden to exceed the permitted payload of the ladder. Check regularly if the ladder is properly
assembled.
Installation
Bestway Inflatables will not be responsible for damage caused to the pool due to mishandling or failure to
follow these instructions.
1. Lay out all parts and check that you have the correct quantities as listed in the components list. If you are
missing any part do not assemble the pool, contact Bestway Customers Service.
2. Spread out the pool and make sure the pool is right side up, let it sit exposed to direct sunlight for 1 hour
or more so that the pool is more flexible during set up.
3. Place the pool near an adequate drainage system to deal with overflow water and ensure the pool's inlet
A and outlet B are correctly positioned to allow your filter pump to connect to a power source.
Note: Do not use extension power cords to power your pump. ATTENTION: Do not drag the pool on the
ground, this can damage the pool.
4. Insert the stopper plugs into inlet A and outlet B on the wall from the inside of the pool.(See Fig.1)
NOTE: For 4.88m x 1.22m (16' x 48"), 5.49m x 1.22m (18' x 48"), 5.49m x 1.32m (18' x 52") pools,
please refer to the connection valve installation on following page.
5. Insert top rail (A) into the pole pockets at the top of the pool. (See Fig.2)
6. Connect top rail (A) with T-Connector (C) at each of corner and insert pins (D) into gasket (F) first and
then into pre-drilled holes of the frame.
NOTE: The gasket cups should face downwards to prevent water leaking into the top rails. (See
Fig.3,4,5)
7. Repeat steps 5 and 6 until all top rails (A) are connected with T-Connectors (C) and the top frame is set
up. For ease of assembly slightly raise the last 2 rails to an inverted v shape and insert into the last
T-Connectors(C). Slowly lower until fully connected taking care not to pinch your fingers. (See Fig.6)
8. Attach all footings (E) to the bottom of the vertical pool legs (B). (See Fig.7)
9. Put all vertical pool legs (B) inside the pool wall band. Connect vertical pool leg (B) into the bottom of the
T-Connector (C) . Make sure the vertical pool leg (B) has the spring loaded pins at the top when
connecting the T-Connector (C). (See Fig.8)
S-S-003501/21.0x28.5cm (圆形支架水池说明书AB版) JS-YF-2015-B-03970/英
All manuals and user guides at all-guides.com
NOTE: For 2.44m x 61cm (8' x 24") pools, no wall band.
10. Pull the frame from different directions to ensure all rails, pool legs and connectors are firmly jointed. (See
Fig.9)
Part code QTY / SET
11. Ensure drain valve is firmly closed. Smooth out the bottom.
12. Put 1" to 2" (2.5cm to 5cm) water in the pool to cover the floor. Once pool floor is slightly covered, gently
P2116
smooth out all wrinkles. Start in the center of the pool and work your way clockwise to the outside.
P61126 14
P61127 14
Fig. 1
P61128 14
P61110 30
P61129 14
P61111 30
56444ASS16/56483ASS16 1
F4H019B-03A 1
P61109
Fig. 4
Part code QTY / SET
P2121
P61130 18
P61131 18
P61096 18
Fig. 7
P61110 38
P61134 18
P61111 38
56427ASS16 1
F4H019B-03A 1
P61132
Connection Valve Assembly
For 4.88m x 1.22m (16' x 48"), 5.49m x 1.22m (18' x 48"), 5.49m x 1.32m (18' x 52") pool model. (See Fig.10)
Part code QTY / SET
P2117(01)
Fig. 10
P61345 16
P61346 16
P61347 16
P61349 34
P61348 16
P61339 34
56451ASS16 1
F4H019B-03A 1
P61340
NOTE: If you want to connect other pool cleaning kits to the pool through the connection valve, use a Phillips
screwdriver to disassemble the Debris Screen from the Connector. (See Fig.11)
Fig. 11
Filling Pool with Water
ATTENTION: Do not leave pool unattended while filling with water
1. Fill pool until water capacity is 90%, DO NOT OVERFILL as this could cause the pool to collapse. In times
of heavy rainfall you may need to empty some of the water to ensure the level is correct. (See Fig. 12.13)
2. When filling the pool is completed, check that the water is not collecting on any side to ensure the pool is
level.
IMPORTANT: If pool is not level, drain water and re-level ground by digging out (See Fig. 14). Never
attempt to move the pool with water in it, serious personal injury or damage to the pool may result.
WARNING: Your pool may contain a great deal of pressure. If your
pool has any bulge or uneven side then the pool is not level, the sides
may burst and the water may discharge suddenly causing serious
personal injury and/or damage to property.
3. Check pool for any leaks at valves or seams, check ground cloth for
any evident water loss. Do not add chemicals until this has been done.
NOTE: In the event of a leak, patch your pool using the Heavy-duty
repair patch provided. Refer to the FAQ's for further information.
Fig. 13
NOTE: Drawings for illustration purpose only. May not reflect actual product. Not to scale.
6
Fig. 2
Fig. 5
Fig. 8
A
Fig. 14
Proper Water Level
Fig. 3
Fig. 6
Fig. 9
B
Fig. 12
0°
S-S-003501