R&G IA0006BK Montageanleitung Seite 14

Page 14 of 18
• Ouvrez le capot de câblage et débranchez les 3 connexions illustrées à la photo 30 et détaillées
ci-dessous :
CONNECTEUR 2 BROCHES BLANC / TRANSPARENT = FEU DE PLAQUE NUMERIQUE
CONNECTEUR NOIR À 3 BROCHES = CLIGNOTANT CÔTÉ GAUCHE
CONNECTEUR 3 BROCHES GRIS = CLIGNOTANT CÔTÉ DROIT
• À l'aide d'une douille de 10 mm, retirez les 4 écrous de fixation du support de la boîte à fusibles
et du support de boîte à fusibles d'origine, comme indiqué sur la photo 31, puis abaissez avec
précaution le support d'origine, tout en introduisant le câblage dans le trou du sous-châssis.
• Retirez les deux boulons situés sur la face inférieure et les deux boulons situés à l'arrière du
support d'origine, pour retirer le cache en plastique, en exposant le câblage, comme indiqué
sur la photo 32.
• Retirez les plaques d'écartement des clignotants illustrées à la photo 33 en déclipsant l'un des
côtés du joint en caoutchouc du clignotant, et appuyez doucement sur les tiges de clignotant
pour retirer les clignotants.
• Installez les mini-clignotants de rechange comme indiqué précédemment, pour l'avant de la
moto puis remontez le support, en vous assurant que tous les feux fonctionnent correctement
avant de prendre la route.
The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design
changes which do not diminish their performance or visual appeal and supplying them in such state shall conform to the order.
The Buyer acknowledges no representation or warranty (other than as to title) has been given or will apply to the Products other
than those in R&G's order or confirmation and the Buyer confirms it has chosen the Products as being of merchantable quality
and suitable for its particular purposes. Where R&G fits the Products or undertakes other services it shall exercise reasonable
skill and care and rectify any fault free of charge unless the workmanship has been disturbed. The Buyer is responsible for
ensuring that the warranty on the motorcycle is not affected by the fitting of the Products. On return of any defective Products
R&G shall at its option either supply a replacement or refund the purchase money but shall not be liable if the Products have
been modified or used or maintained otherwise than in accordance with R&G's or manufacturer's instructions and good
engineering practice or if the defect arises from accident or neglect. Other than identified above and subject to R&G not limiting
its liability for causing death and personal injury, it shall not be liable for indirect or consequential loss and otherwise its liability
shall be limited to the amounts paid by the Buyer for the Products or the fitting or service concerned. These terms do not affect
the Buyer's statutory rights.
Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned direct to us if
they were purchased direct from us (customer must prove if necessary). Otherwise to be returned to original vendor. Goods
must be in re-sellable condition, in the opinion of R&G Racing. All returns are subject to a 25% restocking and handling fee (25%
of the gross value exc. P&P – at the prevailing price at time of purchase). The customer must pay any and all carriage charges.
No returns of discontinued products, unless within 14 days of purchase. This policy does not affect your statutory rights and does
not refer to faulty goods.
Unit
Tel: +44 (0) 420 89007 Fax: +44 (0)
1
ISSUE 1 25/04/2019 (FB)
CONSUMER NOTICE
R&G RACING RETURNS POLICY (NON-FAULTY GOODS)
, Shelley's Lane, East Worldham, Alton, Hampshire, GU34 3AQ
1
420 87301
1
R&G
www.rg-racing.com
IA0006BK
Email: info@rg-racing.com