Verwandte Anleitungen für Tannoy CMS 801 SUB BM
Inhaltszusammenfassung für Tannoy CMS 801 SUB BM
- Seite 1 CMS 801 Series CMS 801 SUB BM/CMS 801 SUB PI 8" Compact Ceiling Mounted Subwoofer for Installation Applications (Blind Mount)/(Pre-Install) CMS 801 PI 8 OHM BACKCAN Back Can for CMS 801 PI Series Ceiling Loudspeakers (Pre-Install)
- Seite 2 11. Use únicamente los dispositivos o accesorios LAB GRUPPEN, LAKE, TANNOY, TURBOSOUND, por un técnico cualifi cado. manufacturer, or sold with cualquier persona por confi ar total o parcialmente en la...
- Seite 3 Um eine Gefährdung durch Stromschlag Standvorrichtungen, chariots, des diables, TANNOY, TURBOSOUND, TC ELECTRONIC, TC HELICON, sans notifi cation. Toutes les marques appartiennent à auszuschließen, darf die Geräteabdeckung Attention Stative, Halter oder Tische, des présentoirs, des pieds...
- Seite 4 Por favor leia o manual de instruções. には決して水分がかからないように注意 tripé, suporte, ou mesa LAKE 、 TANNOY 、 TURBOSOUND 、 TC ELECTRONIC 、 TANNOY, TURBOSOUND, TC ELECTRONIC, TC HELICON, 用されている場合 し、 花瓶など水分を含んだものは、 装置の Atenção especifi cados pelo TC HELICON 、 BEHRINGER 、 BUGERA および...
- Seite 5 MUSIC Group Unpacking MIDAS, KLARK TEKNIK, LAB GRUPPEN, Every TANNOY product and accessory is carefully inspected before packing. After unpacking, please inspect your product to make sure no damage has occurred in LAKE, TANNOY, TURBOSOUND, TC ELECTRONIC, TC HELICON, BEHRINGER, BUGERA transit.
- Seite 6 CMS 801 Series Quick Start Guide Product Feature Identifi cation Accessories Each product is supplied with the following accessories as standard: Fig 1.1: The blind-mount (BM) models come with a pre-fitted back can Tuning Port Euro Type Connector Screws for mounting wings C-Ring Tile bridge kit...
- Seite 7 4. Slide the speaker assembly through the hole and turn the screws to extend the mounting wings. Tighten the screws until a fi rm grip is achieved. If using a power driver, TANNOY recommends a torque setting of 1.5 Nm. DO NOT OVERTIGHTEN! 4.
- Seite 8 Instructions for Optional Pre-Installation Back can (Pi Models Only): An optional plaster (mud) ring bracket is available from TANNOY. This bracket is designed to be pre-installed into newly An optional pre-install back can is available for all pi (pre-install) models. This back can is designed to be pre-installed into newly constructed, non-suspended ceilings.
- Seite 9 CMS 801 Series Quick Start Guide Wiring And Setting Up: CMS 801 sub BM Dimensions: Template hole cutout size: 295 mm 1. Open the wiring cover at the back of the speaker can to access the Euro type connector plug and socket.
- Seite 10 (3) Long term power handling capacity as defi ned in EIA - 426B test A full range of measurements, performance data, and Ease™ Data can be downloaded from tannoy.com Transducers TANNOY operates a policy of continuous research and development. The introduction of new materials or manufacturing methods will always equal or exceed the published specifi cations, which TANNOY reserves the right to alter without prior notice. Low frequency Please verify the latest specifi cations when dealing with critical applications 1x 200 mm (8.00") long throw woofer with multi fibre paper pulp cone...
- Seite 11 Authorized Reseller not be located in your vicinity, you may contact the MUSIC Group Authorized Fulfi ller for your country listed under “Support” at tannoy. com. Should your country not be listed, please check if your problem can be dealt with by our “Online Support” which may also be found under “Support”...