Inhaltsverzeichnis Einführung 1.1 Allgemeine Informationen Bitte lesen Sie die Bedienungsanleitung sorgfältig vor Inbetriebnahme des Gerätes. Bei falscher oder unsachgemäßer Handhabung erlischt der Gewährleistungsanspruch. Hinweis: Falls Sie schon ähnliche Produkte installiert haben, muss die Vorge- 1. Einführung hensweise mit diesem Produkt nicht zwingend übereinstimmen. 1.1 Allgemeine Informationen ..................
2. Installation 1. Einführung 1.4 Systemkomponenten 2.1 Anschluss der Komponenten Montieren Sie das Steuergerät und den Satelliten Receiver im Fahrzeuginneren. Achten Sie auf eine sorgfältige Verlegung der Kabel, um Kurzschlüsse zu vermeiden. Achten Sie Antenneneinheit hierbei auch auf schon vorhandene Kabel. Die elegante Kunstoffhaube schütz die Antenne bestens gegen äußere Witte- Schließen Sie die Antenne wie auf der Abbildung dargestellt an:...
2. Installation 2. Installation 2.2 Das Steuergerät 2.3 Wahl des Standortes Vorderansicht des Steuergerätes Direct Broadcast Service (DBS) strahlt Audio, Video und Daten über den Satelliten aus, der sich in 35 km Höhe über der Erde befindet. Mit einer Empfangsstation wie die An- tenne und einem Satelliten Receiver werden die Signale vom Satelliten empfangen und Satellitenauswahl Ein / Aus Schalter...
2. Installation 2. Installation 2.4 Inbetriebnahme und Bedienung 2.5 Skew Einstellungswerte für europäische Hauptstädte Folgende Einstellungen müssen Sie nur beim 1. Schalten Sie den Fernseher und den Satelliten Receiver ein. Achten Sie darauf, dass die Seaman 37 (ohne Auto Skew) vornehmen. LNB Versorgungsspannung im Receiver eingeschaltet ist.
3. Fehlerbehebung 4. Ausleuchtzone Kein Satellitensignal Seaman 37 Seaman 45 GPS/AutoSkew • Objekte wie Bäume, Brücken und große Häuser, die sich im Einfallswinkel des Satelli- ten befinden, führen zu einem Verlust des Signals. • Wenn das Satellitensignal durch schwere Wetterbedingungen verloren geht, wird das laufende Programm des Receivers beendet (das Bild wird einfrieren, bzw.
5. Aktualisierung der Firmware 5. Aktualisierung der Firmware Updatevorgang: Wenn die Frequenz, auf der die Antenne den Satelliten idendifiziert, abgeschaltet wird, muss ein Firmwareupdate des Steuergerätes durchgeführt werden. 1. Schalten Sie das Steuergerät aus. Die aktuelle Firmware Version des Steuergerätes können Sie in den ersten 3 Sekunden nach dem Einschalten im unteren Bereich des Displays ablesen.
7. Technische Daten Notizen Seaman 37 Seaman 45 Seaman 60 Antennen Typ ............Off-Set-Spiegel ......Off-Set-Spiegel ....... Off-Set-Spiegel Anzahl der Teilnehmer........3 ............3 ............3 LNB Typ..............Universal LNB ......Universal LNB ......Universal LNB Frequenzband .............Ku Band .......... Ku Band ........Ku Band Frequenzbereich ..........10.7 GHz bis 12.75 GHz ..
Seite 9
Seaman 37 Seaman 45 GPS / AS Seaman 60 GPS / AS User manual Stand: 3.0 Mai 2015 // Technische Änderungen, Druckfehler und Irrtümer vorbehalten. Megasat Werke GmbH | Industriestraße 4a | D-97618 Niederlauer | www.megasat.tv | info@megasat.tv...
Seite 10
Content 1. Introduction 1.1 General Information Please read the manual thoroughly before operating the equipment. In case of incorrect or improper handling of the warranty becomes void. Note: If you have already installed similar products, the procedure does not 1. Introduction necessarily coincide with this product.
2. Installation 1. Introduction 1.4 System Components 2.1 Connecting the components Install the control unit and the set-top box inside the vehicle. Maintain a careful instal- lation of the cable in order to avoid short circuits. Pay attention also to existing cables. Antenna unit The elegant plastic housing will protec- Connect the antenna as shown in the illustration below:...
2. Installation 2. Installation 2.2 The contron unit 2.3 Selecting the location Front view of the control unit Direct Broadcast Service (DBS) satellites broadcast audio, video and data information from satellites located 22 miles in space. A receiving station, such as the antenna, should include a dish and satellite receiver to receive the signals and process them for use by Satellite Select On / Off switsch...
2. Installation 2. Installation 2.4 Startup and operation 2.5 Skew setting values for European capitals The following settings are only for the Seaman 37 1. Turn on the TV and the set-top box. The green LNB LED on the display of the control (without AutoSkew).
3. Troubleshooting 4. Footprint No Signal Seaman 37 Seaman 45 GPS/AutoSkew • Objects such as trees, bridges, and large buildings, which are located in the angle of the satellite will lead to a loss of the signal. • If the satellite signal is lost through severe weather conditions, the current program of the receiver is stopped (the image freeze, or disappear).
5. Firmware Update 5. Firmware Update Update process: When the frequency is switched off, on which the antenna idendifiziert the satellite, you must update the firmware of the control unit. 1. Turn off the controller. The current firmware version of the control unit, you can read on the bottom of the screen in the first 3 seconds after switching on.
6. Specifications Notes Seaman 37 Seaman 45 Seaman 60 Antenna typ ............Off-Set-Dish......... Off-Set-Dish ......Off-Set-Dish Users ................3 ............3 ............3 LNB typ ..............Universal LNB ......Universal LNB ......Universal LNB Frequency band ..........Ku Band .......... Ku Band ........Ku Band Frequency range ..........10.7 GHz to 12.75 GHz ..
Seite 17
Status: 3.0 May 2015 // Technical changes, misprints and errors reserved. Megasat Werke GmbH | Industriestraße 4a | D-97618 Niederlauer | www.megasat.tv | info@megasat.tv...