Inhaltsverzeichnis
Werbung
2. SICHERHEITSHINWEISE / SAFETY INSTRUCTIONS
GENERAL SAFETY INSTRUCTIONS FOR ELECTRIC MODELS
• This is not a toy! Suitable for young people under the age of 14 with adult supervision.
• Use the model accordingly to chapter "How To Use" in this instruction manual.
• Assemble the model accordingly to this instruction manual. Do not alter or modify the model. Only use parts that are officially
recommended by Pichler Modellbau.
• Always pay close attention to the manuals that are included to accessory parts (radio system, speed controller, battery etc.).
• Do not fly the model before you have finished the assembly completely according to this manual.
• Before you fly, check all functions of the model carefully.
• Never fly your model near other human beings, animals or other obstacles. You are responsible for flying the model, so
you have to check carefully your flight area.
• NEVER use your model on public streets or near public airports.
• Stop flying immediately if you realize any radio interference.
• Do not touch any moving or hot motor parts during action! Let all components cool down before you handle them.
• Check your model carefully after each flight. Replace parts if they are worn out or if they are defective.
• Keep your hands out of reach from rotating or hot parts of the model.
• Keep in mind that plastic parts easily break under cold temperature conditions.
• If you are a novice in flying you should ask experienced pilots for assistance during your first flights.
• Protect yourself from dust and other small things when you test run your propeller drive on the ground.
• Keep all electronic components dry and clean!
• Take care that your motor does not get overload or gets blocked under full power.
• Let the motor cool down after restarting the model again.
• Charge your batteries carefully. Always watch the charging process and make sure all connectors are in good conditions.
• Do not shorten the battery by connecting the pluspole with the minuspole directly!
• Make sure that the wires do not touch rotating or hot parts of the model.
3. ERFORDERLICHES ZUBEHÖR / REQUIRED ACCESSORIES
• PULSAR Shocky Brushless Motor, # C4308
• LiPo Akku LEMONRC 650-7,4V, # C6722
• Zoom CA Sekundenkleber, # X3571
• Zoom CA Aktivatorspray, # X3573
• 3 x Mini Servo S2112, # C5185
• Brushless-Regler Schnurzz Controller 12A, # C6467
• Luftschraube PWS 8x4.3, # C1240
4
7
6
Nr.
Menge
Bezeichnung
No.
Qty
Description
1
1
Oberes Rumpfteil / Upper Fuselage
2
1
Unteres Rumpfteil / Lower Fuselage
3
1
Waagerechtes Rumpfteil / Horizontal Fuselage
4
1
Linke Tragfläche / Left Main Wing
5
1
Rechte Tragfläche / Right Main Wing
6
1
Höhenruder / Elevator
7
1
Seitenruder / Rudder
8
2
Torsions-Verstärkung / Torsion Strip
9
2
Diffusor, klein / Small Diffusor
10
2
Diffusor, groß / Large Diffusor
11
2
Höhenruder-Diffusor / Elevator Diffusor
12
1
Holm / Spar
13
1
Kunststoffteile / Plastic Frame
13-1
2
Ruderhörner Höhen- & Seitenruder / Horns Elevator & Rudder
13-2
2
Ruderhörner Querruder / Horns Ailerons
13-3
1
Querruder Servoarm-Vergrößerung / Aileron Servo Arm Extension
13-4
2
Fahrwerkshalterung / Landing Gear Mount
13-5
4
Kunststoff-Ring / Plastic Stopper
13-6
2
Verstärkung Radverkleidung / Wheelpant Stiffener
13-7
2
Fahrwerksverstärkung / Landing Gear Reinforcement
13-8
2
Höhen- & Seitenruder Servoarm-Vergrößerung / Elevator & Rudder Servo Arm Extension
14
1
Motorträger / Motor Mount
15
2
Höhen- & Seitenruder-Anlenkung / Elevator & Rudder Linkage (1,5 x 200 mm)
16
2
Querruder-Anlenkung / Aileron Linkage (1,5 x 145 mm)
17
4
Z-Draht / Z-Wire (0,8 x 15 mm)
18
4
Schrumpfschlauch / Shrinktube
19
4
Einstellbare Anlenkung / Adjustable Link
20
4
Sicherung / Fixation
21
2
Fahrwerksstreben / Landing Gear Struts (2 x 200 mm)
22
2
Fahrwerksachsen / Landing Gear Axles (1,5 x 20 mm)
23
1
Faden / Thread
24
2
Rad / Tire (31 mm)
25
2
Radverkleidungen / Wheelpants
Manual Xtreme V3
Bauanleitung Xtreme V3
3
1
4
www.pichler-modellbau.de
4. MONTAGE / ASSEMBLY
2
5
5
Werbung
Inhaltsverzeichnis
