Werbung
Verfügbare Sprachen
Verfügbare Sprachen
VC 6 L MC
Using the dust bag (Figure D)
To remove the dirt/dust from the dust container without any
dust escaping, a disposal bag can be used.
Insert the bag in the dust container. Secure the box at the
front of the dust container in the ribs.
Inserting the hose (Figure E)
Insert the connector in the suction opening (3) for vacuum
cleaning operation. Use the blower opening (4) for blower
operation.
Insert the hose in the connection (1) and twist to lock (2).
Air flow regulator (Figure F)
The air flow can be controlled at the end of the hose by turning
the air flow regulator.
Using a suitable nozzle (Figure G)
All of the nozzles shown can be inserted in the nozzle pipe (1).
The nozzle pipe (3) can be removed for vacuum cleaning by
pressing the clips (1) and pulling out the nozzle (2).
Using the shoulder strap (Figure H)
To use the shoulder strap, insert the clasps in the fasten-
ers. Carry the vacuum cleaner as shown in figure I.
Switching on and off (Figure J)
The main switch of the device has two positions (ON/OFF). The
device is switched on and off by pressing the main switch.
Accessory container (Figure K)
All accessory parts can be stored conveniently on the device.
Troubleshooting
Motor stops:
A thermal overload protector will shut off the motor if the
motor temperature is too high. If this occurs, turn the switch
off. Wait 15-30 minutes for the motor to cool. Turn switch
on and resume operation.
Suction power is reduced:
The tank may be full and needs to be emptied.
The hose and nozzle may be clogged and need to be
cleaned.
Any of the above may be damaged and need to be re-
placed.
The filter may be clogged. Use the Filter Cleaning System
to clean the filter.
Replace the filter or make sure the filter is installed properly.
The hose connection is loose and need to be tightened.
Static shocks:
If the environment is too dry, add moisture to air. If possi-
ble, use a humidifier.
In case the relative humidity of air is low, please note that
this situation will not have any effect on use of the vacuum
cleaner.
Maintenance and care
NOTE
This vacuum cleaner has an integrated thermal overload
protection feature to protect the motor against high tempera-
tures. This can occur under strenuous operating conditions. If
the motor switches off during operation, switch off the device
using the main switch and allow the motor to cool down for 15-
30 minutes. The device can then be switched back on again.
WARNING!
–
Before cleaning and performing maintenance work, switch
off the device and remove the mains cable if the device is
connected to a power supply.
–
Switch off the device before changing to a different function.
–
Maintenance work may only be carried out on this device
by authorised customer service centres or specialists who
are familiar with the relevant safety regulations.
–
Observe the local safety regulations for portable,
commercially used equipment.
–
The manufacturer or an appointed person shall carry out a
technical inspection at least once per year. The filter is
inspected for damage, for example, and the air-tightness of the
device as well as correct operation of the controls are checked.
–
When performing maintenance or repair work, all
contaminated items that cannot be cleaned sufficiently must
be disposed of. Use non-transparent sacks in accordance with
the applicable regulations to dispose of this waste.
–
The outside of the device must be thoroughly cleaned and
freed of any hazardous substances. Alternatively, a sealed
coating can be applied before the device is removed from
the hazardous area.
–
During transport or maintenance of the device, the intake
opening must be sealed using the plug.
–
Danger of harmful dust. Always wear disposable clothing
and masks (P2 or higher) during maintenance work
(e.g. filter replacement).
Cleaning
NOTE
Do not use cleaning agents containing silicone for cleaning.
–
No external assistance is required for the execution of
basic maintenance and cleaning.
–
The outside of the device and the inside of the container
must be cleaned at regular intervals with a damp cloth.
Filter cleaning system (Figure L)
The device is equipped with a semi-automatic filter cleaning
system. It cleans the filter and restores the suction power.
Switch on the device (1) to use the filter cleaning system.
Insert the nozzle pipe in the opening of the device (2) to
close it for air flow and to generate the maximum vacuum
in the dust container.
Press the filter cleaning button three times to clean the filter.
Manual filter cleaning (Figure M)
If the filter is soiled, rinse it in cold water (1) and allow it to
dry (2). Install the filter again once it has dried.
13
Werbung
