Christopeit Sport GT 4 Montage- Und Bedienungsanleitung Seite 18

Computer instructions for 9814
The enclosed training computer provides high convenience in training.
All values relevant to the training are displayed in a corresponding window.
From the beginning of the training session onwards, the required time,
the current speed, the approximate energy consumption, the travelled
distance and the current pulse rate are displayed. All values are recorded
incrementally for zero upwards. If the training session is to last for a
particular period, a particular number of calories is to be consumed, a
particular distance travelled and a particular pulse rate not exceeded,
these values can be entered individually or as combinations.
The computer is switched on by briefly pressing one of the buttons or
simply by beginning a training session. Select the desired function for
input by pressing the "F" button. The function which can be changed is
displayed.
Each desired value can be entered by pressing the two arrow buttons.
The „+" and „-" button stand for an increasing value starting from zero
and also for a decreasing value starting from the maximum value.
If all displayed values are to be deleted, press and hold the "F" button.
To start the computer, simply begin your training session. The computer
then begins to measure and display all values.
To stop the computer, simply end the training session. The computer
stops all measurements and holds the last achieved values. The last
reached values in the functions TIME, CALORIES and KM are stored
and training can proceed with these values when the training session is
resumed.
The computer switches off automatically approx. 4 minutes after the
training session has ended. All values reached by then are erased.
Displays:
A. Dual function display "PULSE" + "CALORY"
1. "TIME" display:
Usually, the currently required time is displayed in minutes and seconds.
A particular value can be specified using the „+" and „-" buttons. Is a
particular time has been specified, the remaining time is displayed. When
the specified time has elapsed, this is indicated by an acoustic signal.
In this function, the last reached time is stored until the computer switches
off.
(Maximum limit of the display is 99.59 minutes.)
2. "KM/H" display:
The current speed is displayed n kilometres per hour. A particular value
cannot be specified with the „+" and „-" buttons. The last achieved
value is not stored in this function.
(Upper limit of the display is 99.9 km/h)
3. "CALORY" display:
The current amount of consumed calories is displayed. A particular
value can be specified with the „+" and „-" buttons. If a particular
consumed amount is specified, the amount of calories remaining to be
consumed is displayed. When the specified value is reached, this is
indicted by an acoustic signal.
In this function, the last reached time is stored until the computer switches
off.
(Upper limit of the display is 999 calories)
4. "KM" display:
The current value of the travelled kilometres is displayed. A particular
value can be specified with the „+" and „-" buttons. If a particular distance
is specified, the distance remaining to be travelled is displayed. When
the specified value is reached, this is indicated by an acoustic signal.
In this function, the last reached time is stored until the computer switches
off.
(Upper limit of the display is 999 km)
5. "PULS" display:
The current pulse rate is displayed in beats per minute. A particular
value can be specified with the „+" and „-" buttons.
If a particular pulse rate limit is reached, this is indicated by an
acoustic signal.
In this function, the last reached time is stored until the computer
switches off.
(Upper limit of the display is 40- 240 pulse beats per minute)
Buttons:
1. „+" and „-" buttons:
The specified values of the individual functions can be entered in steps
by each pressing of these buttons. The desired function must firstly be
selected using the "F" button.
After training has begun, the display counts down from the specified
value to zero.
2. "F" button:
By pressing this button briefly, it is possible to change from one function
to another, i.e. the respective functions can be selected in which entries
are to be made with the arrow buttons.
„Temperature" – display:
This shows you the actually surrounding temperature.
This display is showed only in the left display, when computer is without
action.
Uhrzeit -display:
This display shows what time it is. The time can be set by taking out and
removing the batteries of the computer and adjusting the hours and
minutes with „+" and „-" buttons. Please enter each one with „F" button.
This display is showed only in the bottom display when computer is
without action.
18