Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Loading the baskets
According to EN60436
Upper basket
Lower basket
3 Cutlery rack:
NOTE: Please place the light flat wares on the shelf. The total weight is
less than 1.5kg.
4 Curlery basket:
Information for comparability tests in accordance with EN60436
Capacity: 10 place settings, Position of the upper basket: lower position,
Program: ECO, Rinse aid setting: MAX, Softener setting: H3
Starting a cycle wash
•
Draw out the lower and upper basket, load the dishes and push
them back. It is commended to load the lower basket first, then the
upper one.
1 Cups
2 Saucers
3 Glasses
4 Mugs
5 Dessert bowls
6 Glas bowl
7 Dessert dishes
8 Dinner plates
9 Soup plates
10 Melamine dessert plates
11 Melamine bowl
12 Oval platter
13 Small pot
14 Cutlery basket
1 Soup spoons
2 Forks
3 Knives
4 Tea spoons
5 Dessert spoons
6 Serving spoons
7 Serving forks
8 Gravy ladies
•
Pour in the detergent (see the section entitled Salt, Deter- gent and
Rinse Aid ).
•
Insert the plug into the socket. The power supply is 220-240 VAC
/50 HZ, the specification of the socket is 10A 250VAC. Make sure
that the water supply is turned on to full pres- sure.
•
Close the door, press the Power button, to switch on the machine.
•
Choose a program, the response light will turn on. Then press the
Start/Pause button, the dishwasher will start its cycle.
Change the program
A wash cycle can only be changed if it has been running for a short time
otherwise, the detergent may have already been released and the dish-
washer may have already drained the wash water. If this is the case, the
dishwasher needs to be reset and the detergent dispenser must be re-
filled. To reset the dishwasher, follow the instructions below:
1
Press the Start/Pause button for more than 3 seconds, the machine
will pause.
2
Rotate the knob to select the desired programme.
3
Press the Start/Pause button, after 10 seconds, the dishwasher will
start.
Forgot to add a dish
A forgotten dish can be added any time before the detergent cup opens
1
Open the door a little.
2
After the spray arms stop working, you can open the door com-
pletely.
3
Add forgotten dishes.
4
Close the door
5
The dishwasher will start running again.
6
Press the Start/Pause Button, the dishwasher will run after 10 se-
conds.
At the end of the Wash Cycle
When the working cycle has finished, the buzzer of the dishwasher will
sound for 8 seconds, then stop. Turn off the appliance using the ON/OFF
button, shut off the water supply and open the door of the dishwasher.
Wait for a few minutes before unloading the dishwasher to avoid han-
dling the dishes and utensils while they are still hot and more susceptible
to break. They will also dry better.
Switching Off the Dishwasher
The program light is on but is not blinking, only in this case has the pro-
gram ended. Open the door.Switch off the dishwasher by pressing the
ON/OFF button. 2.Turn off the water tap!
Open the door carefully.
Hot dishes are sensitive to shocks. The dishes should cool down for
around 15 minutes before removing from the appliance. Open the dish-
washer's door, leave it ajar and wait a few minutes before removing the
dishes. In this way they will be colder and the drying will be improved.
Unloading the dishwasher
It is normal for the dishwasher to be wet inside.
Empty the lower basket first and then the upper one. This will avoid wa-
ter dripping from the upper Basket onto the dishes in the lower one.
Warning: It is dangerous to open the door mid-cycle, as hot steam
may scald you.
Werbung
