Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Before using your dishwasher for the
first time:
A
Set the water softener
B
Add 1.5Kg dishwasher salt and then full fill the salt container with
water
C
Fill the rinse aid dispenser
D
Fill in detergent
Water softener
The water softener must be set manually, using the water hardness dial.
The water softener is designed to remove minerals and salts from the
water, which would have a detrimental or adverse effect on the opera-
tion of the appliance. The higher the content of these minerals and salts,
the harder your water is. The softener should be adjusted according to
the hardness of the water in your area. Your local Water Authority can
advise you on the hardness of the water in your area.
Adjusting Salt Consumption
The dishwasher is designed to allow for adjustment in the amount of salt
consumed based on the hardness of the water used. This is intended to
optimise and customise the level o f salt consumption.
1
Switch on the appliance;
2
Press the Start/Pause button for more than 5 seconds to start the
water softener set model within 60seconds after the appliance was
switched on;
3
Turn the selector to select the proper set according to your local
environment, the sets will change in the following sequence: H4-
>H5->H6->H1->H2->H3;
4
Press the On/Off button or no operation for 5 seconds to end the
set up model.
WATER HARDNESS
°dH
°fH
°Clarke
mmol/l
0-5
0-9
0-6
0-0,94
6-11
10-20
7-14
1,0-2,0
12-17
21-30
15-21
2,1-3,0
18-22
31-40
22-28
3,1-4,0
23-34
41-60
29-42
4,1-6,0
35-55
61-98
43-69
6,1-9,8
Note 1
1 dH=1.25 Clarke=1.78 fH=0.178mmol/l
Clark: British degree
fH: French degree
DH: German degree
Note 2
The manufactory setting: H4 (EN 50242)
Your local Water Authority can advise you on the hardness of the water
in your area..
Selector Po-
Salt
con.
sition
(cykl/1kg)
H1 - glass
0
H2 - 90 min 9
H3 - 90 min
12
+ glass
H4 - ECO
20
H5 - ECO +
30
glass
H6 - ECO +
60
90 min
Loading the salt into the Softener
The salt container is located beneath the lower basket and should be
filled as explained in the following:
Attention!
•
Only use salt specifically designed for the use in dishwashers! Every
other type of salt not specifically designed for the use in a dish-
washer, especially table salt, will damage the water softener. In
case of damages caused by the use of unsuitable salt the manufac-
turer does not give any warranty nor is liable for any damages
caused.
•
Only fill with salt just before starting one of the complete washing
programs. This will prevent any grains of salt or salty water, which
may have been spilled, remaining on the bottom of the machine for
any period of time, which may cause corrosion.
A
After the lower basket has been removed, unscrew and remove the
cap fromthe salt container.
B
Place the end of the funnel (supplied) into the hole and introduce
about 1.5kg of dishwasher salt.
C
Full fill the salt container with water, it is normal for a small amount
of water to come out of the salt container.
D
After filling the container, screw the cap tightly back clockwise.
E
The salt warning light will stop being after the salt container has
been filled with salt.
F
Immediately after filling the salt into the salt container, a washing
programshould be started (We suggest to use a short program).
Otherwise the filter system, pump or other important parts of the
machine may be damaged by salty water. This is out of warranty.
Important!
1
The salt container must
only be refilled when the
salt warning light in the
control panel comes on.
Depending on how well
the salt dissolves, the salt
warning light may still be
on even though the salt
container is filled. If there
is no salt warning light in
the control panel (for
some Models),you can es-
timate when to fill the salt
into the softener by the cy-
cles that the dishwasher
has run.
2
If there are spills of the
salt, a soak or a rapid pro-
gramshould be run to re-
move the excessive salt.
Always use the salt intended for use with dishwasher
Werbung
