Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Power connection
For personal safety:
•
Do not use an extension cord or an adapter plug with this appliance.
•
Do not, under any circumstances, cut or remove the earthing.
Electrical requirements
Please look at the rating label to know the rating voltage and connect
the dishwasher to the appropriate power supply. Use the required fuse
10 amp, time delay fuse or circuit breaker recommended and provide
separate circuit serving only this appliance.
Connection from the power cord.
Ensure the voltage and frequency of the power being corresponds to
those on the rating plate. Only insert the plug into an electrical socket
which is earthed properly. If the electrical socket to which the appliance
must be connected is not appropriate for the plug , replace the socket,
rather than using a adaptors or the like as they could cause overheating
and burns.
Water connection
Cold water connection (safety hose)
The appliance must be connected to the water mains using new hose-
sets. The old hose-sets should not be reused.
Water pressure must be between 0,04 MPa and 1 MPa. If the pressure
is below the minimum consult our Service Department for advice.
1
Pull The safety supply hoses completely out from storage compart-
ment located at rear of dishwasher.
2
Tighter the screws of the safety supply hose to the faucet with
thread 3/4inch.
3
Turn water fully on before starting the dishwasher.
The safety supply hose consists of the double walls. The hose's system
guarantees its intervention by blocking the flow of water in case of the
supply hose breaking and when the air space between the supply hose
itself and the outer corrugated hose is full of water.
A hose that attaches to a sink spray can burst if it is installed on the same
water line as the dishwasher. If your sink has one, it is recommended
thet the hose be disconnected and the hole plugged.
If the water pipes are new or have not been used for an extended period
of time, let the water run to make sure that the water is clear and free
of impurities. If this precaution is not taken, there is a risk that the water
inlet can get blocked and damage the appliance.
1
Turn off the water.
2
Unscrew The safety supply hose from the faucet.
Connection of the drain hose
Insert the drain hose into a drain pipe with a minimum diameter of 4cm,
or let it run into the sink, making sure to avoid bending or crimping it.
The free end of the hose must be at a height lower than 60cm and must
not be immersed into water to avoid the backflow of it.
How to Drain Excess Water From Hoses
If the sink is more than 1000 mm higher than the floor, the excess water
in hoses cannot be drained directly into the sink. It will be necessary to
drain excess water from hoses into a bowl or suitable container that is
held outside and lower than the sink.
Water Outlet
Connect the water drain hose. The drain hose must be correctly fitted to
avoid water leaks. Ensure that the water drain hose is not kinked or
squashed.
Extension Hose
If you need a drain hose extension, make sure to use a similar drain hose.
It must be no longer than 4 metres, otherwise the cleaning effect of the
dishwasher could be reduced.
Start a dishwash
The following things should be checked before starting the dishwasher.
1
The dishwasher is levelled and fixed properly
2
The inlet valve is open
3
To avoid any water leak, check if inlet valve is correctly screwed to
the dishwasher
4
The wires are tightly connected
5
The power is switched on
6
The inlet and drain hoses are knotted
7
All packing materials and printings have been removed from the
dishwasher
Attension: After installation, please make sure to keep this manual. The
content of this manual is very helpful to the users.
Error codes
Before you call service, look at the following
When some malfunctions come on, the appliance will display error
codes to warn you:
Codes
Rapid indicator fleets frequently
•
Longer inlet time.
•
Faucets is not opened, or water intake is restricted,or water pres-
sure is too low.
ECO indicator fleets frequently
•
Overflow.
•
Some element of dishwasher leaks .
90 Min and rapid indicators fleet frequently
•
Not reaching the required temperature .
•
Malfunction of the heating element .
Warning: If overflow occurs, turn off the main water supply before call-
ing a service. If there is water in the base pan because of an overfill or
small leak, the water should be removed before restarting the dish-
washer.
Werbung
